SPONSORS
2024 ICRBE EXPO |
Results 1111 - 1140 of 1255
11 years ago
Bill Sidney
1111. Re: Thanks PacBay!
they are great to the builder both HOBBY an the FULL TIME PERSON
Forum: rodboard 11 years ago
Bill Sidney
I never liked to shortern a rod I would look for a different rod to fit your requirements , I think you will be happer a I know some people will tell you they do it all the time but I don't . there again I am a new person at building rods , just remember the rod is yours an you fish it an live with it no matter what you do to it , an you can build the blank any way you want
Forum: rodboard 11 years ago
Bill Sidney
when it is cold out or in my basment I use HOT tap water to heat up the epoxy the 2 part flex coat one is clear an one is light yellow the clear one will harden up , but but the bottle in hot wap water an it will
melt so you can mix an use it , it don't have to be hot just warm [ put it in pants pocket will take a long time ] , some people use micro wave [ never tried it ]
Forum: rodboard 11 years ago
Bill Sidney
the epoxy I use is in excss of 9 years old an doing fine you should not have that problem with any of the thred type I know of , look at every thing you are doing to see if you can find out why ,,
do a test wrap on a scrap rod [ CP don't use it ] as like you a new at it
Forum: rodboard 11 years ago
Bill Sidney
1115. Re: Nano guides
' pam " spray cooking oil , ask wife / girl friend comes in a spray can , in fact olive oil might work [ have not tried it yet ]
Forum: rodboard 11 years ago
Bill Sidney
normaly the smaller guides are for light to very light rodes so for th most part you will only get single foot in the smaller size I could be wrong but i don't think so
Forum: rodboard 11 years ago
Bill Sidney
have youlooked atice fishing guides don't know if it is what you want but they go to 2.5
Forum: rodboard 11 years ago
Bill Sidney
to start out look at a lot of ""' you tube "" there is a lot on " you tube " it will give you a lot to soak up an a lot of ideas
Forum: rodboard 11 years ago
Bill Sidney
1119. Re: Wood stain on cork?
on all of the colored / stained cork , the color will fade over time if you want to keep the cplor you have to coat it with some thing , this is because cork will not take a color it just coats the out side , an will rub off of faid from the sun I think
Forum: rodboard 11 years ago
Bill Sidney
anglers work shop carries a unfinished blanks give them a call they seem to know what they are doing they are a supporter on the left
Forum: rodboard 11 years ago
Bill Sidney
1122. Re: Skeleton Reel Seats
looks cool I like it know nothing about it but looks good
Forum: rodboard 11 years ago
Bill Sidney
the action will change , but it is in the eyes of the fisherman not the fish , the fish don't care
Forum: rodboard 11 years ago
Bill Sidney
1124. Re: parts? catalogue
what kind of parts ??? reel parts ? lure parts? fishing rod parts ? car parts ? just kidding about the car parts we might help but more info please
Forum: rodboard 11 years ago
Bill Sidney
1125. Re: float rod guides
there was a artical in one of the books about 1 to 2 ago an the man that wrote the artical did a real good job on it it help me a lot look to back issues I think
Bill
Forum: rodboard 11 years ago
Bill Sidney
1126. Re: threadmaster
you will here lots of wayes to mix an an use , you will have to try some an find one that works for you , I even but some DNA in my mix when mixing to help with the bubbles , as I mix small amounts in a 1 TB messuring spoon , I hold the spoon in my hand to warm it up then but 1 or 2 drops of DNA on top after the mix an warming an all the bubbles are gone , your brush can add to the brubble p
Forum: rodboard 11 years ago
Bill Sidney
had the same problem I found that if I applied a lot of epoxy at one time , do the out side than put on a large amount at a high speed [ speed counts] I use about 30 rpm than change to a slow speed about 10 rpm , stop the motor wripe off the excess that drops , down than start the motor an it should take care of your problem in stopping the moter this is a short time , some people use a
Forum: rodboard 11 years ago
Bill Sidney
I an going to San Diego Calf. in March an looking for a fishing Rod supplier around there , can some one supply there mane an address Thanks Bill
Forum: rodboard 11 years ago
Bill Sidney
1129. Re: roller guide feet
make sure you but an under wrap on the rod under the guides so when the rod flexes the guid move on the under wrap an not wear on the rod some people don't do the under wrap
but over the long run you will find it works great on the heavyer rods
Forum: rodboard 11 years ago
Bill Sidney
if all fails get a welder [ electric ] an heat the rod up as you will be removing the center of the grip an you will sand it out to fit the blank , , the welder tkraws pipes that way an it will work the
metal rod will get very hot an will not burn the grip
Forum: rodboard 11 years ago
Bill Sidney
1131. lookin for a crappie rod
I have a need to build a crappie rod for bank fishing 2 / 3 / 4 , pice rod about 8 FT long steer me in the right direction please as I am lost on this type of rod
Bill
Forum: rodboard 11 years ago
Bill Sidney
i don't know much about ferrule's but I think they are married an you might have to get the pair so they fit not sure but ?? I could br wrong more people will chme in on this i am sure
Forum: rodboard 11 years ago
Bill Sidney
1133. Re: 2-piece
bamboo cooking sticks an tape works for me [ ask your wife for some ]
Forum: rodboard 11 years ago
Bill Sidney
no matter who you talk to you will allways find a horror story , peole handle the package an if people handle it there be accidents , I like USPS , they have a very good name with me an i use plastic water pipe
one end closed off an a screew fitting on the other end ,
Forum: rodboard 11 years ago
Bill Sidney
I d on't think ant thing will hold up much in rod holders [ rod holders are hard an the handles are soft somewhat so the softest thing takes a beatting ]
Forum: rodboard 11 years ago
Bill Sidney
mud hole has some black body [ alum. ] the 2 nuts to hold the reel on an the hoods are silver , I just got a size 17 in , if need be i can dig up the part number let me know if you can't find them
PS it was a channel lock I think for the reel to set down in a little bit just let me know if you can't find it will supply, Bill
Forum: rodboard 11 years ago
Bill Sidney
1137. cork reaming rods
I need to redo my rods , wha't is the best way? use contact glue or epoxy as my binding cement with sanding belts cut up need some input please
thanks SID
Forum: rodboard 11 years ago
Bill Sidney
1138. cork reaming rods
I need to redo my rods , wha't is the best way? use contact glue or epoxy as my binding cement with sanding belts cut up need some input please
thanks SID
Forum: rodboard 11 years ago
Bill Sidney
speed up the drying if you are going to polish it , put it the warmest part of the house to help the drying time some , an I don't mean "" high heat "" 75 deg would greatly help a lot in my part of the world
the heat means a lot , [ ALASKA } then polish it out if not cut it off an do again now as the Flex coat will only get harder over time , so make your mine up
Forum: rodboard 11 years ago
Bill Sidney
1140. Re: SIZE OF REEL SEATS
I thank you all for your 2 CTS I can work with that see you on the water
SId
Forum: rodboard |