SPONSORS
2024 ICRBE EXPO |
Current Page: 1 of 1
Results 1 - 23 of 23
13 years ago
Tony Woodruff
Great then.
Im wanting to build a MHX frog rod spiral, this will be my first spiral build. Is there any more tips you guys have beyond Tom's book i have. I will copy his degrees he says but was wondering if there was anything else added up to this day?
Forum: rodboard 13 years ago
Tony Woodruff
ok, I had a conversation with a fella that said he wouldn't use spiral on a rod that uses less than 15# line, this is why I was asking.
His oppinion was spiral should start at 15 pound line and up.
Forum: rodboard 13 years ago
Tony Woodruff
3. spiral wrap
is there a limited line weight for it? like 6#?
Forum: rodboard 13 years ago
Tony Woodruff
4. waxing?
what are ya guys using again on keeping your rods cleaned with? was it simple wax?
Forum: rodboard 13 years ago
Tony Woodruff
I was able to re-use the tip top, I lost exactly 7/8 inch of tip, already fished her and Im happy, thanks for the advice fellas
Forum: rodboard 13 years ago
Tony Woodruff
Tip top installed with 5 minute epoxy, and i didn't use a flame for bubbles. only times i used a flame was on my keeper wrap, tiger wrap and my #12 guide, this was my procedure Bob. As for the tension wraps, i wrapped loose on tiger wrap and tip top, others tighten as seen needed upon build.
i will try to post pics if i can get one that picks up the detail.
I may need to do something for
Forum: rodboard 13 years ago
Tony Woodruff
No Bob, I did not split a tip on the build, I was mentioning about needing to now if I was to match up with my #4 guides.
But the origanle build was built normal tip NO split.
Since I have you here on this, what is your opinion on the rod look of a explosion snap?
Forum: rodboard 13 years ago
Tony Woodruff
Alex where's this article? I would love to learn more on the apperance of breaks. Like I said this to me looks like a explosion?
By the way, its a MB782 and I have another, I bought 2, the others my son's and if the same happens to it I'll let ya guys know, Untill then all is well and Sean & Mark convinced me its worth it to salvage it.
I need to match up a tip to my #4 micros and I d
Forum: rodboard 13 years ago
Tony Woodruff
I see two rods not three on this subject?
Gary H. its not a clean break and its not splintered, it looks to me like a explosion?
You think its a build issue?
Again, MHX Blanks are Just Fine, nothing to see here. Just a fellow builder wondering if he should fix it and move on.
Forum: rodboard 13 years ago
Tony Woodruff
it looks like an inch is what i lost on the tip.
As for MHX blanks I would buy another, IMHO they are great. Theres nothing wrong with them Bob R. im just asking if its worth fixing or replacing cause im not sure?
With losing a Inch, how much would that change the rod, I used it for throwing plastics?
Forum: rodboard 13 years ago
Tony Woodruff
I got to decide on claiming my first warranty, Is it worth going thru it or replace the tip?
Like to hear from fellow rod builders on this, I have alot of work in it and was wondering if its worth just keeping it and replace the rod tip instead of sending it back and hopefully get the rod replaced, I know that I'd have to get new hardware and my stickers and such. I just never have claimed a w
Forum: rodboard 14 years ago
Tony Woodruff
Cool Ron, it for sure looks like a 1970's album cover. That brings back some memorys' lol
I used .015 sized glitter. kept it thinned. I'll try and take a pic of it tomorrow.
Forum: rodboard 14 years ago
Tony Woodruff
13. Glitter & finish
was wondering if anyone has played around with this? I did alittle today, I didn't lay it on too thick, and now Im thinking of doing a tiger wrap this way, add giltter to the first stage of wrap, then lay the second wrap on top with no glitter, don't know if this will affect the 3-D very much?
What ya think?
Forum: rodboard 14 years ago
Tony Woodruff
I had a pacbay minima exposed reel seat I never used and well i used it, I need a pointer on what instrument to use for sealing up the edge on the hardest side so no water gets thru, its the model GMC165 spinning ,
the inside curve degree is what I gotta do, Not the straight flat side where you simply stand the pole up right. I was thinking 5 minute epoxy so it would not have a chance to run
Forum: rodboard 14 years ago
Tony Woodruff
Any special offer for shipping for those of us that would like to buy a bottle right now to try? Don't hurt to ask, lol
Forum: rodboard 14 years ago
Tony Woodruff
wow, that would change alot of things for me, I haven't tried other things on a build because of fear that my finish might screw up, looks intresting to me to get some.
way to go guys
Forum: rodboard 14 years ago
Tony Woodruff
So, Im thinking correct-give it a try,lol
thanks fellas, and Walker I did that there to my first one, burnished the last wrap also. I like it alot
Forum: rodboard 14 years ago
Tony Woodruff
18. Tiger wrap X 3
Did my first Tiger wrap and really enjoyed it, has anyone tried to push it further? instead of twice wrapped how about three times wrapped?
Curious
Forum: rodboard 14 years ago
Tony Woodruff
James, I love those grips man, I ever make me a casting rod, I'd love to try that. Killer job!
Forum: rodboard 14 years ago
Tony Woodruff
Mark Griffin Wrote:
-------------------------------------------------------
> Tony Woodruff Wrote:
> --------------------------------------------------
> -----
> > acid rod requires a 20 dollar minimum purchase
> it
> > appears,
>
> If you read on when you see that message, you'll
> see that we accept orders under $20 by phone. The
> reason for thi
Forum: rodboard 14 years ago
Tony Woodruff
acid rod requires a 20 dollar minimum purchase it appears,
is there a local nylon thread supplier? I,ve never been forced to look.
Forum: rodboard 14 years ago
Tony Woodruff
Thanks fellas, its only the first coat so, I know im gonna have to be carefull. This all started because i was trying to clean up bleed off from F.C. color preserver. Im mad at myself for completely not cleaning off the bleed off first. I figured I would after i applied the first finish coat, lesson learned.
so I want to save this build, its my first MHX rod build and first TigerWrap as well
Forum: rodboard 14 years ago
Tony Woodruff
23. Block sand epoxy
Hello all, i've just been building rods the last 14 months with my now 12 yrd son, we love it and by the way nice book Tom.
i have been using search feature for all qurstions with results up till now.
question is how can one smooth out a finish that has lent and finger prints on it? only thing i have found is Tom's comment on block sand the rap, regarding a tigerwrap?
if i can sand out
Forum: rodboard
Current Page: 1 of 1
|