SPONSORS
2024 ICRBE EXPO |
Results 1291 - 1319 of 1319
15 years ago
Barry Thomas Sr
1291. Re: Rod Dryers
Brendan; if you can e-mail me at junkmansj@yahoo.com I can send you a link
Forum: rodboard 15 years ago
Barry Thomas Sr
1292. Re: removing cork tape
goo be gone or goof off might work, at the local hardware store
Forum: rodboard 15 years ago
Barry Thomas Sr
just added a picture of a Alps on a CTS 13' 6" Surf rod I built and use a lot! Dry wall tape arbors and Kar-dol
Forum: rodboard 15 years ago
Barry Thomas Sr
1294. Re: Finish Motors????
Oh well, still hidden. if you come back junkmansj@yahoo.com
Forum: rodboard 15 years ago
Barry Thomas Sr
1295. Re: Finish Motors????
Bob your email is hidden, I have some info for you
Forum: rodboard 15 years ago
Barry Thomas Sr
1296. Re: Gaff Question
My last one I used Kar-dol. Shoved a styrofoam peanut in from the back end and packed it full, installed the hook. I was using a cut-off piece of a calstar blank (butt). had to grind the little tail piece to get it in.
Forum: rodboard 15 years ago
Barry Thomas Sr
Get Urethane tape available from merrick, I use the rubber 3M tape
Forum: rodboard 15 years ago
Barry Thomas Sr
alot of the beach sharkers on the gulf coast yak the baits out, not cast them
Forum: rodboard 15 years ago
Barry Thomas Sr
just sent a 7 footer to Ontario Can. to my Son,2" PVC tube. USPS 6 days arrived just fine. Wrapped it in a length of foam pipe insulation and some bubble wrap spacers
Forum: rodboard 15 years ago
Barry Thomas Sr
Dennis; unhide your e mail address and i'll send you some photos or send email to junkmansj@yahoo.com
Forum: rodboard 15 years ago
Barry Thomas Sr
1303. Re: Cork tape
you should not have any problems with it sticking, I have one here thats 10 years old. All I did was wipe it with Alcohol
Forum: rodboard 15 years ago
Barry Thomas Sr
1305. Re: lathe
check out Penn State Industries, they have some nice lathe's
Forum: rodboard 15 years ago
Barry Thomas Sr
1306. Re: Under-wrap finish?
Brush on the finish then use the brush "DRY" to take of the excess finish so you only have a thin "wet Coat"
Forum: rodboard 15 years ago
Barry Thomas Sr
Ned; I believe that those rivets only secure the top hood to the seat,it does not go thru blank
Forum: rodboard 15 years ago
Barry Thomas Sr
1308. Re: Thread puller loops
10# powerpro with a yarn flag (so I can find it)
Forum: rodboard 15 years ago
Barry Thomas Sr
have built several,NO problems great stuff love my SU 1209!
Forum: rodboard 15 years ago
Barry Thomas Sr
1310. Re: Cork Tape
I use a Wall paper seam roller, works well
Forum: rodboard 15 years ago
Barry Thomas Sr
is the reel seat metyal if so try a little heat to release the butt section (if not Blank thru butt)
or cut seat off with Dremel tool, -cut on both sides and pop parts off with a Screw driver then lose the fore grip and rebuild
Forum: rodboard 15 years ago
Barry Thomas Sr
1312. Re: Cork Tape
I have had cork tape on my rods for 5-7 years using only back adhesive and a butt cap / thread wrap ramp, still works fine. Still has that grippy feeling
Forum: rodboard 15 years ago
Barry Thomas Sr
1313. Re: CTS blank warranty
I'll Second That, Great people there!!
Forum: rodboard 15 years ago
Barry Thomas Sr
1315. Arrow Cast Casting Rod
Found this today! Seems to be a CO-2 fired casting rod, less than 4 feet long has a foam covered metal butt grip that holds the CO-2 cartridge. And a heavy chrome plated reel seat with a moving bolt like a rifle with a thumb accuated trigger. I believe it must have had a shaft of some sort that lanched a bobber or something? Blank is hollow with two guides and a sliding 8-10" tip section
Forum: rodboard 15 years ago
Barry Thomas Sr
1317. Fenwick SU1366
was given to me today, Does anyone have any info lure weight? line weight? it is now around 10 feet is that factory length?
Forum: rodboard 15 years ago
Barry Thomas Sr
Maderia Thread has a lot of colors near lime green, I used #1935
Forum: rodboard 15 years ago
Barry Thomas Sr
2X the diameter of the ferrule, I mostly build Surf rods and Double Wrap the Ferrule wrap
Forum: rodboard |