SPONSORS
2024 ICRBE EXPO |
Results 151 - 180 of 854
3 years ago
Dennis Danku
Fuji BHNOG aluminum oxide heavy duty frames. A real work horse of a guide.
Forum: rodboard 3 years ago
Dennis Danku
Pac-bay PBX series. Very affordable. 10 and 11 ft , 2 piece blanks.
Forum: rodboard 3 years ago
Dennis Danku
Tip/Tops in sizes from #8 tube to #14, and #12 guides casting and spinning. Other than that you better start collecting every rod component known to man because you never know what will come in the door next. If you really want to start repairing rods every and any thing related to fishing rods will at some point be useful. You just have to have space for it. I've been repairing rods for over 30
Forum: rodboard 3 years ago
Dennis Danku
Trust your retailer on this info, just in case something is wrong you can avoid the cost of return shipping. I don't think any third party would want to get involved in that.
Forum: rodboard 3 years ago
Dennis Danku
Fuji "UNG" Hardloy Boat Rod Guide with High Frame Design UNG10 Bright.USG was a Gunsmoke finish with a SIC insert.
Forum: rodboard 3 years ago
Dennis Danku
Rawhide lacing, the same stuff used to tie up your boots years ago.
Forum: rodboard 3 years ago
Dennis Danku
158. Re: fishing shoes
Lookup this shoe by Skechers #204112. It's called the relaxed fit Tresman Rivero men's sandal.
Forum: rodboard 3 years ago
Dennis Danku
159. Re: Broken fly rod
Henry, Can you please post a picture of your fly rod so I can see the color of the blank and if you have a caliper can you measure the O.D. of the section of where the top half mates up to. I have a lot of StCroix broken fly rods and might have a tip section for you.
Forum: rodboard 3 years ago
Dennis Danku
160. Re: Renzetti Lathe
Chris, Check with flex-coat, they came out with a motor with variable speeds and reverse just about a month ago.Looks like a good system.
Forum: rodboard 3 years ago
Dennis Danku
Don't do any scrapping, just put another correctly mixed coat over it. It WILL be fine.
SORRY I DIDN'T READ THE FULL POST. IT's time for the heat gun and the utility knife. Sparingly warm the thread wraps and then cut along the feet to remove the guides. You should be able to unravel the remaining thread.Use a Scotchbrite pad to smooth things out and then rewrap.
Forum: rodboard 3 years ago
Dennis Danku
Only ONE rod! Check your email Glenn.I suggest you check PAC-BAY Duralite Sleeves Models DLSS.
Forum: rodboard 3 years ago
Dennis Danku
163. Re: 19th Anniversary
Thank you Tom and all of you who contribute to making this forum what it is. Before finding this site,( Since 1977) the only new ideas I got was when I went to sportsmen shows or tackle shops to look at new rods and how they were built. In the 1980's I went to a BASS fishing show somewhere near Cherry Hill,NJ where I got o meet Tom Mann (a big guy), and I also got to meet a guy and see his line o
Forum: rodboard 3 years ago
Dennis Danku
Glenn, Thru the years of ordering stock, I have mispurchased some slick butt tubes much too small for the Bunkerspoon rods I build for use here on Raritan Bay. With a length of 10" , an O.D.of 1.133' and an I.D. of 0.800"- 0.834" these would be perfect for your use on fresh water trolling rods. They are new , come with trim rings (if you need them). Color is black plastic or nylo
Forum: rodboard 3 years ago
Dennis Danku
What do you do when you need to save the seat but it has to come off?
Forum: rodboard 3 years ago
Dennis Danku
I'll put it in the mail tomorrow morning. My return address will be on it. I have plenty that I'm not using, I'm just glad you can use them.
Forum: rodboard 3 years ago
Dennis Danku
Frank ,Send me your address and I'll get one out to you on Friday morning. It wont be a Lakeland but it will look like it. Might even be better quality. Just refund the Postage amount.
Forum: rodboard 3 years ago
Dennis Danku
168. Re: New Rod Blank
Get a sanding block with 120 grit and go to town on it. Knock off the high spots and then drop down to a finer grit like 220. It'll only take about 15 minutes to come up with a nice smooth blank just like from the factory.
Forum: rodboard 4 years ago
Dennis Danku
I always did like Permagloss but if you were lucky enough to get a bottle that wasn't partially solid and could use all of it, which was rare I switched to CpXtra and never had a problem since.
Forum: rodboard 4 years ago
Dennis Danku
No , it's an old AMTEK model, Eglass, with a fast taper,7'6". Used to extend them with a Tuff Butt and the finished rod would be 9'.
Forum: rodboard 4 years ago
Dennis Danku
Thanks, Took advantage of the black, 7'4" Heavy blanks for Flukein' in Raritan Bay.
Forum: rodboard 4 years ago
Dennis Danku
I would like to take advantage of this offer but I get no response when I hit the SHOP NOW button. Happy Birthday Hunter.
Forum: rodboard 4 years ago
Dennis Danku
Camillo, I would suggest that you check all those guides in the tip section for a rough spot in the rings. Look for cracks, burs or anything that could be slowing the line down in that area. It seems like something is choking your line causing it to back up on itself.
Forum: rodboard 4 years ago
Dennis Danku
Roger pick me up at exit 9 on the NJ turnpike. I'll be the guy on the side of the road with a case of beer under one arm and an empty 5 gal bucket in the other. It's gonna be a long bumpy ride.
Forum: rodboard 4 years ago
Dennis Danku
178. Re: small rod guides
My wife found these little wooden clothespins that are used for holding notes/memos on the fridge door. Well one ended up on my bench and with a little help from my belt sander it is now about 3/16 " wide at the nose and perfectly holds those micro guides near the rod tip.
E Z on E Z off, their made of wood so you can file a valley in the nose to accept the guide foot on one jaw and another
Forum: rodboard 4 years ago
Dennis Danku
The cow that kicks the least is the one you'll end up milking.
Forum: rodboard 4 years ago
Dennis Danku
180. Re: Call-out
Here at The Cannibalistic Soup kitchen a lot of people depend on you so, PLEASE BE PROMPT, and by all means, ENJOY THE BEING DIP.
Forum: rodboard |