Thank you Tom K. for confirming what I was taught a long time ago. I just read the Q&A section of RM (vol #8 #4). I learned almost 20yrs. ago that a rod blank dosn't know or care what type of components one mounts to it. It is what it is and one can utilize it's strengths and or weeknesses however they please. Now please excuse this not so short rant! I had not been involved
Forum: rodboard

Thanks Chuck and Spencer, My brother wanted me to build it as a spinning rod. He and I are happy to know thats what it was designed for! Slammin hook-ups all
Forum: rodboard

Hi all, My Brother sent me a Fenwick SH962 2 piece 8' honey fiberglass blank. I assume the "SH" refers to "steelhead" and I think this is a 8wt or 10wt flyrod blank but not really sure? Is anybody familiar withthis blank? I emailed Fenwick but no reply yet. Maybe I need to call them. I do know this blank is about 20 yrs old. Thanks in advance,
Forum: rodboard

Custom Tackle will have several to chose from in that price range as will Neal's I bet. Try CUI also! Good Luck
Forum: rodboard

Hi Steve, I'm building a heavy/fresh - med/salt 15-40lb. jig stick (1st bumper rod) and I'm using double foot guides through out. With this rod, obviously, guide weight is not a factor but strength is. Anything lighter and I would use the single foot guides 99% of the time. The high quality of todays single foot guides makes them the first choice for me when ever possible. As you know
Forum: rodboard

Hey Ray, I saw your listing in the directory. If you would like to chat drop me a line. Thanks,
Forum: rodboard

After realizing the actual topic that started this thread, I too wanted to give my thanks to all of the participents who helped bring the article in RM to fruition. OUTSTANDING!! Can't wait to read the 2nd part !! Putting my hands together to everyone!!
Forum: rodboard

Fred, I'm with you! Reading threads discussing articles writtin about in an issue of RM that I am waiting for just makes the waiting that much more unbareable! WAAAAAAAAA!! Mick & Steve, We are also of the same mind set. I am still just a hobbyest who sells rods to keep the hobby from breaking the bank! I have put a lot of myself (thread art included) into all of the rods I have sold a
Forum: rodboard

Hey Derek, What part of No. Cal. ?
Forum: rodboard

Aaron, Acording to what I have read on the board, it would depend on the knots that might need to pass through the guide (s). Use only the largest needed and stay as small as possible. And Have Fun!!
Forum: rodboard

Ditto! Sam, I built an Ultra-Light 2pc. spinning rod using a "Tiger-Eye" blank I also bought thru @#$%& and am very impressed with it! Spent less than $30.00.. Used the Amtak rainbow zerconium guides and the rootbeer color blank really pops. If I were to build another one I would probably try a lighter set of guides. The Amtak's look sweat but I think they are a bit heavy.
Forum: rodboard

Contact Dan Craft. He is one of the board sponcors on the left. He has some awesome blanks and provides top notch customer service. I just received an 8wt 5piece and like I said, Awesome!! Happy Casting!!
Forum: rodboard

Hi Steve, If you do not want to become a rod builder I suggest you find someone to re-build the baitcaster for you. There is a good chance if you do it yourself, you will contract the dredded "rod builders addiction"! As of yet, there is no cure!! Where do you live? You might be able to find a builder in your area by checking the directory here. Good luck in what ever you deci
Forum: rodboard

Hi Andrew, Try the FAQ and Library of this board while you waite for someone to chime in. I do not have any experiance with permagloss so can't help you myself. Good Luck,
Forum: rodboard

Try Shikari or the Rainshadow blanks. I've built several of the Shikari 1 piece and my clients have loved them!
Forum: rodboard

Hi Eijiro, IMO I believe it would be pretty hard to over-heat the blank with a hair dryer. Be very very careful if you use anything else like an alcohol lamp, propane torch, or cigarette lighter. Look into the FAQ & Library sections of this board for some quick suggestions on this subject. Most of the old epoxy should come off with your finger nail if not try, a plastic scrapper or dish
Forum: rodboard

I would build the Batson. However, Dan Craft has some 8wt. 5 piece blanks on clearence if you want save some $ on a quality blank try him! his link is on the left of the page. Smooooth Wraps!!
Forum: rodboard

Thanks for the compliment Ralph, I was concerned that you might be offended. I normally do not plagerize. Note: Tried to email you but the email was returned! Smooth Wraps!
Forum: rodboard

Hi Chris, General rod building is ok to do indoors with no special ventilation needed unless you are using paints or solvents or other things like that. Putting thread to the blank requires no chemicals but you will have read the lables on the glues and or epoxy you are using. I have my rod jig set up in my garage and have no problems. I'll take the blank into the back yard to apply paint or
Forum: rodboard

I have never heard a fish bite unless it was smashing a surface lure!!
Forum: rodboard

None Taken Mike, It's all good!! as my son would say!
Forum: rodboard

Enough clowning, In a way, I am new to rod building as I lost the addiction for almost 15 yrs! I have since the last holiday season picked it back up again and only since May have I found this board and really got serious about blank construction, componant construction and placement, and the other technical aspects of the craft that I once took for granted. There have been many new develop
Forum: rodboard

Got it Steve, Get my reply?
Forum: rodboard

It's thinkers like Cliff that feeds my craving for INPUT ! Hats off to him and others! Off topic : My wife is wondering if I can be cured or not? I tell her it's better than cats scratch fever!! I think I need an attorny! LOL !!
Forum: rodboard

Mike, Yes, I am a glutton and an addict! My wife also has prescription for 800mg. Tylenol for which I am very gratefull. NEED INPUT !! LOL ! LOL ! LOL !
Forum: rodboard

Here Here Mike! Qucker and easier!! But I am also waiting for more input! ( like #5, I love INPUT!! )
Forum: rodboard

There is an earlier thread on this subject. Very interesting! Do a search!
Forum: rodboard

Bill, You must be from the old school as am I. I was taught the term "SPLINE" not SPINE as well. LOL!!
Forum: rodboard

Steve, Interested in selling the 5 ft piece you are not happy with?
Forum: rodboard

Hey Mike, What is your price range? Spinning or casting? 1 piece or 2 piece? Action? Your options are endless! Check the sponsors on the left. I would recommend all of them.
Forum: rodboard