SPONSORS
2024 ICRBE EXPO |
Results 151 - 180 of 1255
4 years ago
Bill Sidney
151. Re: Trolling Blank
some thing different ??? try a spiral wrap it is just what you need on a trolling rod , the rod in the holder it will not want to roll nearly as much with the spiral wrap , I think , could be wrong
Forum: rodboard 4 years ago
Bill Sidney
no problem , I would not apply Flex coat to your wraps till warmed up , out side of that , no problem , just kidding go to it , warm up before building , I think
Forum: rodboard 4 years ago
Bill Sidney
try this one lots out there under SDS
SDS / MSDS Database Search - Safety Data Sheets Library | MSDSonline ] try this [
Forum: rodboard 4 years ago
Bill Sidney
156. Re: Ice Rod Blanks
what type fish are you after PAN size or Lakers ? or bigger ? in a tent / house or on the ice ?
Forum: rodboard 4 years ago
Bill Sidney
Roger thanks for the INFO will take it an go . will stop using it as a mix , thanks again
Forum: rodboard 4 years ago
Bill Sidney
Roger I don't under stand when I started, I was showed that if the epoxy had some bubbles on or in it, an you put one or two drops on the mixed epoxy , one will do all the bubbles go to the side an pop,
never tried acetone , the DNA. just caused a temp. change to the top of the mixture , I never did mix it in just applied it went on fine . just let the DNA. evaporate , what is the short comi
Forum: rodboard 4 years ago
Bill Sidney
after mixing your epoxy let set 30 sec, then drop one or two drops of DNA on top of epoxy , watch what happen's
to the bubbles in the epoxy , don't mix after the DROPS just use , it works great for me , still a beginner learning
Forum: rodboard 4 years ago
Bill Sidney
JB is stiffer than the 2 ton stuff , should work just fine .,the reason we use ROD BOND a lot , is it is stiff like putty , I think ,
Forum: rodboard 4 years ago
Bill Sidney
JB is stiffer than the 2 ton stuff , should work just fine .,the reason we use ROD BOND a lot , is it is stiff like putty , I think ,
Forum: rodboard 4 years ago
Bill Sidney
do let us know what you do on your build , it is your build an what goes is all up to you, an what you like , no 2 people will have the same answer for your problem ,
# 1 it is not there problem ,
# 2 the builder will use what ever they have on hand to finish the build an look good , as I see it ,
Forum: rodboard 4 years ago
Bill Sidney
I don't doubt that, but if you look a s set of guides on a new blank that has BLUE / BLACK guides the tip guides seam to wear the most , YES ??????????? or am I out in LEFT FIELD ??
Forum: rodboard 4 years ago
Bill Sidney
FLY LINE $$$$$$ want to keep as long as I can, a little better guide MIGHT HELP a little , I hope
Forum: rodboard 4 years ago
Bill Sidney
You could put a soft one that is wide under the dimple one , push it down wrap a 1/4 to 1/2 inch wrap to hold it down. if need be use D size thread , then epoxy over it all , job finished ,
Forum: rodboard 4 years ago
Bill Sidney
one option Dremel Battery operated, an spray the cut area with a spray bottle [ WATER ], that would do a lot of BLANKS with no dust I think an safe around water, [ BATTERY OPERATED }
Forum: rodboard 4 years ago
Bill Sidney
also A hobby store for model planes , RC or control line will have what you need
Forum: rodboard 4 years ago
Bill Sidney
Have used an have built on them, not a bad blank / rod for the money you will be happy with them
Forum: rodboard 4 years ago
Bill Sidney
one of the big action places on the web is listing some on there site good luck
Forum: rodboard 4 years ago
Bill Sidney
Welcome aboard Chris looking forward to doing business with you ,
Forum: rodboard 4 years ago
Bill Sidney
Have you look at Mudhole web site, they have version , but it is there brand , very close to what you are looking for ,
Forum: rodboard 4 years ago
Bill Sidney
174. Re: Guide alignment
every one has there own way for alignment, they are different but also the same what way works for you . as I see it ,
Forum: rodboard 4 years ago
Bill Sidney
it is as stated before , spin goes for the lighter bait, where casting works real well on the heavey- er bait, as I see it ,
Forum: rodboard 4 years ago
Bill Sidney
176. Re: Rod finish?
I like hot water to heat with , takes a little longer but don't have to baby sit it , also buy in smaller amounts is you don't build a lot ,
Forum: rodboard 4 years ago
Bill Sidney
Mud hole has a tool to make them , I think , an they have a sale going on now ,
Forum: rodboard 4 years ago
Bill Sidney
Have you looked at MUD HOLE drying tent , just an idea , I know nothing about it, out side of what I got from there book ,
Forum: rodboard 4 years ago
Bill Sidney
when going Tuna fishing if you want it to last you will need some good equipment, not cheep equipment , it will last a lot longer, that is what I think
Forum: rodboard |