SPONSORS
2024 ICRBE EXPO |
Results 151 - 166 of 166
18 years ago
Jeff Leonard
151. Re: Musky Rod Handle
Have you considered turning the handle in three sections, being careful to get the proper diameter where they meet and hand sand after gluing. Keep in mind you don't want a heavy glue seam where they meet.
Forum: rodboard 18 years ago
Jeff Leonard
152. # of Coats
I am interested in your opinion. How many coats of lite build finish you all use for the inscription and cross wrap area on size A thread, light spinning rod? I assume the guides require less. Also, your thoughts on size D for med heavy casting rods. I don't think I am using enough lite coats.
Thanks,
Jeff
Forum: rodboard 18 years ago
Jeff Leonard
153. Re: Major Concern
OK, I will apply the first few inches of tape to my pant leg from now on. If alcohol may damage a blank, what is the suggested solvent for removing epoxy from the blank after gluing up the handle?
Jeff
Muskyfsh
Forum: rodboard 18 years ago
Jeff Leonard
154. Re: Major Concern
Cliff & John,
Thank you for your responses to my problem. Cliff ,I will definately keep your advise in mind for future consideration. John, you are correct the blue tape is painters tape and should not pose any problems what so ever. I can only imagine what would have happened if I used Doc Ski's recommendation of using Nashua tape on this blank ( no disrespect Doc you are the best). I am
Forum: rodboard 18 years ago
Jeff Leonard
155. Re: Major Concern
Tom,
It is an honor to have someone of your stature to respond to my problem so quickly. These particular blanks have been my favorite for the last few years for musky blanks and have never had a problem. I usually build my handles directly on the blank due to the fact that they are fairly long and somewhat large in inside diameter. The only thing that I do is wipe down the blank with alcohol
Forum: rodboard 18 years ago
Jeff Leonard
156. Major Concern
I just finished a weave that took me about 4 days to complete using 3M blue masking tape on the blank. While removing the tape from the blank , graghite fibers came off with the tape. I have been building rods for over twenty some years and have never seen this before. I however do not do many weaves. What the ???? went wrong.
Frustrated,
Muskyfsh
Jeff Leonard
Forum: rodboard 18 years ago
Jeff Leonard
Lynn,
Pure genius, why didn't I think of that? My only concern is premature wear on the belt where it rubs on itself, other than that , brilliant idea! You have saved my day.
Happy Turning,
Jeff (muskyfsh)
Forum: rodboard 18 years ago
Jeff Leonard
158. Help? Reverse motor
I just purchased a Custompower wrap and found that the motor rotates in the opposite direction I need it to for my application. When tunring handles on the rod I use interal expansion grips and the unit spins in the direction to lossen them.
Anyone know of a way to reverse the direction of rotation for the motor. If not I guess I go back to my 25 year old home made lathe.
Thanks a bunch for you
Forum: rodboard 18 years ago
Jeff Leonard
159. U-40 Rod Bond
I just recently purchased U-40 Rod Bond for the first time and was wondering how most of you measure out equal amounts.
Thanks ,
Jeff
Forum: rodboard 19 years ago
Jeff Leonard
160. Which Adhesive?
I would like to know what the prefered adhesive is for mounting rubber butt caps to cork.
Thanks,
Jeff Leonard
Forum: rodboard 19 years ago
Jeff Leonard
Sorry everyone, my age is starting to show. Those specs for the preceding post should have been as follows: Tip- 8mm, Butt- 14mm, Length 4'10"
That should make a world of difference in your suggestions.
Thanks Again
Jeff
Forum: rodboard 19 years ago
Jeff Leonard
162. Bamboo Blank Ideas?
I have had these 5 bamboo blanks laying around for 20 years and never knew what to do with them. Any ideas would be appreciated. Specs are as follows: Tip- .8mm, Butt- 1.4mm, Length 4' 10"
Thanks,
Jeff
Forum: rodboard 19 years ago
Jeff Leonard
163. Re: walleye blank
Tom,
Try a St. Croix -SCIII blank, pretty hard to beat for the quality and price, not to mention the fine action.
Forum: rodboard 19 years ago
Jeff Leonard
164. Diamondback Source
Anyone know of a source for Diamondback musky blanks that carry them in stock and can provide me with specs on these blanks. Had no luck emailling Diamondback.
Thanks,
Jeff Leonard
Forum: rodboard 19 years ago
Jeff Leonard
165. Re: Flames
Thanks for all the help, great pics. My first notion was to try marblizing but after viewing the weaves I have to think about it, I guess it just comes down to the question of time.
Measure twice, wrap once.
Jeff Leonard
Forum: rodboard |