Building another spinning rod. This one is for boondogging and jigging for steelhead. Using MICROWAVE guides for the first time. Do I set the stripping guide using the straight-edge method and the choke with Tom's 27X formula like I always do? Thanks Harry
Forum: rodboard

There we go. This is more of what I was looking for. Thank you. And Thank you EVERYONE who responded to my post. You guys are the best
Forum: rodboard

What I learned to do was hold the blank by the butt with the tip on the floor and extended away from me at about a 45 degree angle to the floor. Gently apply pressure as close to the middle of the blank length as you can reach. The blank will roll to one side or the other. I mark that side with a grease pencil or a 1/4 inch piece of masking tape. Then I release the pressure and roll the blank a
Forum: rodboard

Sorry for what? Your explanation was the best one for me. It helped me understand what the other guys meant. So....Thanks
Forum: rodboard

Building my 1st fly rod. It is 11' 7wt. Do I use the same "straight-edge" method I've used to set the stripping guide on spinning rods? I think I can figure out the rest, but advice is always appreciated (i.e. usually needed). Thanks Harry
Forum: rodboard

I have a craftsman band saw I just purchased. When I use it the band curves to the right and I cannot get a straight cut. What should I do? Thanks, Harry
Forum: rodboard

Thanks Chuck. Just what I was looking for.
Forum: rodboard

Hey people. Anyone aware of a source of multi tinted acrylic block in dimensions suitable for turning to build grips(handles) for spin/cast and fly builds ?? I want swirls like you'll find in acrylic blanks for turning pens Thanks HT
Forum: rodboard

I am trying to buy cork block from Cork4U. Cannot get through by phone, and have sent two messages from their site. I need cork block in green, blue and red. Anglers Workshop is backordered for at least 2 weeks. Anyone know how to buy from Cork4U online? Or how do you order from them. Anyone have another source for cork block other than natural and brown colors? I do not want yoga blocks
Forum: rodboard

Does anyone know where to buy cork block in a variety of colors/mixes online? How do you buy from Cork4us? Thanks Harry
Forum: rodboard

Did you mean you cut the grooves WITH the calipers?
Forum: rodboard

I use turning tools. Can you explain what you meant by lexan and 3/8" tape? Thanks
Forum: rodboard

Morning. Learning to turn. Currently turning birch bark. I need advice on how to make the grip the exact same diameter throughout the full length. Also, after going through the full series of grits to get it completely smooth , what do you guys recommend for a finish? I want to bring out any golden tones it may have. Finally, I've been studying you tube tutorials. Are there any hands on classe
Forum: rodboard

I first used elmers woodglue. Now I'm trying Gorilla Glue. Seems to hold well so far
Forum: rodboard

best advice, Jimmy. Thanks
Forum: rodboard

Thanks, Roger
Forum: rodboard

Just tried to order a lock nut mandrel from Mudhole. Out of stock, so I'll get one later. Currently I have it on a 3\8" threadsall, locked down with washers and wing nuts. I drilled a dimple on one end of the threadsall for the tailstock and I'll lock the other end into a drill chuck at the headstock. Comments?
Forum: rodboard

Thanks for the great info. What company/website/store did you purchase the psi tools from?
Forum: rodboard

I am still learning woodturning and am turning a birch bark grip on a Central machinery floor lathe(Harbor Freight). I am having trouble with the bark separating as I turn using a jaw chuck and spindle. I would use a mandrel but need to know how to secure the workpiece to the steel mandrel(MudHole) without the piece slipping. Any help? Thanks
Forum: rodboard

I cannot afford a high quality lathe, so I'm considering purchasing a lathe from Harbor Freight. Anyone have any experience with one??
Forum: rodboard

Has anyone ever turned wood from a tulip tree? Is it any good?
Forum: rodboard

Problem with PVC is the weight
Forum: rodboard

Any advice or suggestions for a blank to be used with spinning reel to JIG for STEELHEAD? 1/8oz to 3/8oz jigs. River fishing from a boat. Thanks guys
Forum: rodboard

it means "stock of weapons" LOL
Forum: rodboard

I know this isn't specifically on rodbuiding, but I've read many posts here that show we have some experienced quality fishermen on board. I'm searching for the stealthiest braid with maximum castability for steelhead. Any suggestions? Is Spiderwire EZ Braid in anyone's armamentarium? Thanks
Forum: rodboard

Thank you for detailing why my thought about adapting a fly reel seat to a spinning application would not work. I appreciate that.
Forum: rodboard

I have always used graphite for my spinning reel seats, but my next spinning build will have an aluminum seat. Are there any suppliers that have a more diverse product line for them? Also, is it possible to cut the end cap from a fly reel seat and adapt it to a spinning rod? Thanks
Forum: rodboard

Sounds right, Roger. Thank you
Forum: rodboard

Mike was always ready to help with advice and suggestions whenever I posted here. Really sad to hear of his struggle. God bless him and his family.
Forum: rodboard

I am rebuilding a graphite spinning rod and need to remove the reel seat and cork grip. I think I read somewhere that boiling water may work. Any suggestions?
Forum: rodboard