SPONSORS
2024 ICRBE EXPO |
Tru Oil finish method
Posted by:
Kevin Bergeron
(---.no.no.cox.net)
Date: February 01, 2014 10:59PM
I have been using Tru Oil for finish for the last few years with good to great results. I generally apply four coats with my finger without sanding between coats. Can I get better results with sanding between coats? If so, what do you guys use to sand before applying a new coat? Finally, do you guys use your fingers to apply and how many coats are applied till you reach your desired results? Thank you gentlemen. Re: Tru Oil finish method
Posted by:
Wes Motsinger
(---.triad.res.rr.com)
Date: February 01, 2014 11:51PM
I use a paper towel to apply. and do 2 coats and no sanding. i like the look Re: Tru Oil finish method
Posted by:
Michael Blomme
(---.direcway.com)
Date: February 02, 2014 12:57AM
I use small cosmetic sponge foam to apply. I sand between coats with 800 grit paper. I use a total of four coats--I like that look too.
Michael Blomme Re: Tru Oil finish method
Posted by:
Ray Zarychta
(---.ri.ri.cox.net)
Date: February 02, 2014 07:45AM
Finger an "sand" with 0000 steel wool, prefer 4-5 coats for high gloss look. Ray Zarychta Glastonbury, CT Re: Tru Oil finish method
Posted by:
john timberlake
(---.triad.res.rr.com)
Date: February 02, 2014 08:17AM
It all depends on what you are applying it to. I like it on corks and put a flood coat then wipe off the excess after a few minutes. It will bring out the grain and soak in while still leaving a cork feel. That is my preference as i don't like glossy cork. I think there are better finishes for woods, though tru oil will work fine. Re: Tru Oil finish method
Posted by:
Scott Hovanec
(---.hsd1.pa.comcast.net)
Date: February 02, 2014 09:14AM
If its on burl cork, I apply it with a paper towel while it turns on the lathe.....just enough to make the cork change color, then I take a dry paper towel and remove any excess. Its able to be handled and mounted immediately. If its for a reel seat insert. I apply with my finger while turning on th lathe. 4-6 coats with a light scuff between coats to remove any high spots or dust that might have landed. After the last coat, I polish up to 12k micromrsh and apply a coat of furniture polish. Re: Tru Oil finish method
Posted by:
Eric Viburs
(---.mpls.qwest.net)
Date: February 02, 2014 09:54AM
I apply with a cloth sanding with 000 or 0000 between every 4 or so coats until all voids are filled. This depends on the material I am applying to. As little as 4 or so and as many as 15. Re: Tru Oil finish method
Posted by:
Steve Hartzell
(---.mid.suddenlink.net)
Date: February 02, 2014 01:42PM
Are there any pics on the photo site that shows how the Tru oil changes the color of the cork? Does it waterproof or protect the cork or is it mostly cosmetic? Steve Hartzell Lake Conroe - Willis, Texas Re: Tru Oil finish method
Posted by:
Ralph Daigle
(---.speed-burst.com)
Date: February 03, 2014 09:11AM
Light sanding between coats removes lint and minor blemishes and each coat will get smoother and smoother. Re: Tru Oil finish method
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: February 03, 2014 09:56AM Re: Tru Oil finish method
Posted by:
Eric Viburs
(---.usar.army.mil)
Date: February 03, 2014 05:07PM Re: Tru Oil finish method
Posted by:
Tim Demond
(172.56.11.---)
Date: February 10, 2014 11:00PM
Is tru oil the best finish for cork? What other options are available? I am building a Tenn, handle and not crazy about how it looks. I am looking for a more finished look. Sorry, only registered users may post in this forum.
|