SPONSORS
2025 ICRBE |
Closed wrap question....
Posted by:
Francis Santangelo
(---.dyn.optonline.net)
Date: December 19, 2023 01:15PM
I want to try my first closed wrap and am trying to figure out the amount of threads i need for which colors and to successfully close the wrap.
I have the visual wrap software which is good for visualizing the wrap but does not account for thread size or count as I would imagine some of you know. Is there a calculation that people use to figure this out or do I just have to spend all the time on this, cut and restart if i fail miserably? I will use either fuji A or D thread on an inshore blank with the butt end diameter of 11 and tip end diameter of 9.7 Pros and cons to either A or D? Thanks in advance for any help. Re: Closed wrap question....
Posted by:
Tom Kirkman
(Moderator)
Date: December 19, 2023 01:18PM
Just keep wrapping until you have the wrap closed in. You won't "fail" miserably. You will have to pack a bit more towards the top end of the wrap and burnish and spread a bit more towards the butt end of the wrap. Some will use Taper Offset Spacing for more precision but honestly unless there is a very steep taper along your wrap length I've not found it necessary.
........ Re: Closed wrap question....
Posted by:
Michael Ward
(---.atlagax1.pop.starlinkisp.net)
Date: December 20, 2023 11:29AM
If you don't have it, I recommend Decorative Wraps by Billy Vivona. It goes into the details on how to calculate things - along with many other helpful details on doing a closed wrap. I look at VisualWrap and DecorativeWraps as going hand-in-hand
VisualWrap will give you the details you need for tapered spacing, which you should use for a closed wrap to help things close out evenly. Be VERY meticulous with your layout threads to the spacing and pack to the spacing marks. As to calcul;ating the space needed for the close - Size A, and Maderia is about 4.1 threads per mm. Most doing closed decorative wraps are using A as it looks better, and with all the crosspoints in a closed wrap is going to allow you to pack it easier - in fact this is a benefit of Maderia threads - the silicone in the thread helps it slide a bit - but you MUST use mutliple coats of color preserver to seal the thread (and the silicone) so it does not affect your epoxy. Michael Ward Back Creek Custom Rods E-mail - backcreekcustomrods@gmail.com Phone - (336) 437-4114 Web: www.backcreekcustomrods/coloredguides.html "Life's too short to fish a boring rod" Re: Closed wrap question....
Posted by:
Mike Ballard
(---.ip-54-39-133.net)
Date: December 20, 2023 06:26PM
IF a customer wants a wrap and a closed wrap at that I look at the particular blank. On a shorter blank with lots of taper I will use a TOS layout. If the blank is something like a 11 or 12 foot surf rod I do not bother. The area in front of the seat and foregrip will have so little taper you can just manipulate the thread in there. Don't make things hard on yourself, its not rocket science. Re: Closed wrap question....
Posted by:
Mark Brassett
(---)
Date: December 21, 2023 09:02AM
What is a closed wrap? Re: Closed wrap question....
Posted by:
Tom Kirkman
(Moderator)
Date: December 21, 2023 09:30AM
A closed wrap is made by continuing to wrap threads until there is no underlying blank or under wrap showing in-between the main center pattern threads.
.......... Re: Closed wrap question....
Posted by:
Francis Santangelo
(---.dyn.optonline.net)
Date: December 21, 2023 07:25PM
Worked off of he plan I had in visual wrap. Had o add a few to fully close bu not much. Happy with how it came out thanks for the help. Sorry, only registered users may post in this forum.
|