SPONSORS
2024 ICRBE EXPO |
Salvaging a glued up handle and reel seat
Posted by:
jon tobey
(---.sf-cable.astound.net)
Date: August 19, 2023 09:29PM
So, I'm in a strange bind. I glued up my handle and reel seat, but then discovered my blank had a broken ferrule. So I want to salvage the handle and reel seat to put it on another blank.
Is there a chemical which will dissolve the Rod Bond or am I drilling this out? Or does the hive mind have another suggestion? jontobey@yahoo.com www.gointothelight.wordpress.com Re: Salvaging a glued up handle and reel seat
Posted by:
Norman Miller
(Moderator)
Date: August 19, 2023 10:00PM
Which part of the ferrule is broken, the tip section or butt section? If the tip section, you may be able to get a new tip or a new blank from the manufacturer’s warranty. At the very worst, you may have to buy a new blank, and then use tip section from it. If it’s the butt section part of ferrule is broken, then you have to think about removing the reel seat and grip. If the reel seat and grip were installed using foam arbors you may be able to remove them using a cork borer. If foam arbors were not used it becomes more difficult to remove the grip, but still possible.
Norm Re: Salvaging a glued up handle and reel seat
Posted by:
Daryl Ferguson
(47.214.193.---)
Date: August 19, 2023 10:45PM
You don't need to use any chemicals. You can use heat (cautiously) to loosen up the glue. Some folks simply hold the rod handle a couple of inches over boiling water with good results. I experimented with an old broken rod by cutting it down and putting the handle area in the oven on 300 (IIRC) for a few minutes and the grip ad reel seat came off very easy. I've since used the reel seat on another project with no ill effects whatsoever. Re: Salvaging a glued up handle and reel seat
Posted by:
jon tobey
(---.sf-cable.astound.net)
Date: August 19, 2023 11:44PM
It's the butt section, and it's on a 10' blank, which I don't even know how I got. So it's coming off. Re: Salvaging a glued up handle and reel seat
Posted by:
jon tobey
(---.sf-cable.astound.net)
Date: August 19, 2023 11:44PM
Thank you! Re: Salvaging a glued up handle and reel seat
Posted by:
Grant Darby
(---.sf-cable.astound.net)
Date: August 20, 2023 10:58AM
On a 10' rod, you may be able to get the butt cap off, cut the rod at the top of the foregrip and fit a new blank inside. Re: Salvaging a glued up handle and reel seat
Posted by:
Chris Catignani
(---)
Date: August 20, 2023 01:49PM
Grant Darby Wrote:
------------------------------------------------------- > On a 10' rod, you may be able to get the butt cap > off, cut the rod at the top of the foregrip and > fit a new blank inside. I would definitely try this ^ Re: Salvaging a glued up handle and reel seat
Posted by:
roger wilson
(---)
Date: August 20, 2023 09:14PM
Jon,
Save your self a lot of frustration. Take 10 minutes and cut the grip and reel seat off your blank. The, use a new grip and reel seat and use arbors in the reel seat, all sized that are the same size as the butt of the rod, unless you want to cut off the one or two guides and are on the butt section and then you can use conventional techniques to place your rear grip and reel seat to the rod blank. Or - leave everything as it is, anc cut off the broken parts of the ferrule and simply make a splice at that point and make the rod a single piece rod. Of course you have to have the ability store and transport a one piece 10 foot rod. A third choice is to simply chop off the grip and reel seat and fore grip if you have one about 4 inches above the parts that you want to salvage. Then, just use a splicing technique to attach the current butt grip, reel seat, fore grip and the short section of blank to the new rod blank. Chop off a corresponding section of the new blank to maintain rod length and you will be set. That way you don't have to disturb the butt cap, rear grip, reel seat and fore grip if there is one on the current rod. I would simply use in inner sleeve and an outer sleeve to accommodate the splice and you will be good to go. The splicing of the rear grip, reel seat, and fore grip and short section of the current rod blank is only about a 15 minute job. === Note: I did this exact thing for a new rod that I had built. Then, after building the rod and delivering it, the customer wanted a change made in the shape of the grips on the rod. I used my full length rod lathe but made a mistake in the way that I had mounted the rod on the rod lathe and as the rod was spun up to full speed, it suddenly went into destructive oscillation and exploded. But, I cut off the butt section of the rod including the grip, reel seat, fore grip and a short section for splicing and spliced it onto a new rod blank and the customer still has that same rod today that has caught many many fish for him over the years. Note, In building many many rods using the full length rod lathe for grip work, this was the only rod blank that I ever damaged as a result of using a rod on the full length rod lathe. --- Personally, I tried to reuse a reel seat and or grip one time, that was a miserable failure and as a result I have never ever tried to reuse these components again by removing them from their current rod. For myself, the few $$ required for a new grip and reel seat - relative to the overall value of the rod, that I would never ever attempt to reuse any grip or reel seat a 2nd time. Take care Best wishes Edited 1 time(s). Last edit at 08/20/2023 09:17PM by roger wilson. Sorry, only registered users may post in this forum.
|