I
nternet gathering place for custom rod builders
  • Custom Rod Builders - This message board is provided for your use by the sponsors listed on the left side of the page. Feel free to post any question, answers or topics related in any way to custom building. When purchasing products please remember those who sponsor this board.

  • Manufacturers and Vendors - Only board sponsors are permitted and encouraged to promote and advertise products on the board. You may become a sponsor for a nominal fee. It is the sponsor fees that pay for this message board.

  • Rules - Rod building is a decent and rewarding craft. Those who participate in it are assumed to be civilized individuals who are kind and considerate in their dealings with others. Please respond to others in the same fashion in which you would like to be responded to. Registration IS NOW required in order to post. You must include your actual First and Last name and a correct email address when registering or posting. Posts which are inflammatory, insulting, or that fail to include a proper name and email address will be removed and the persons responsible will be barred from further participation.

    Registration is now required in order to post. You must include your actual First and Last name and a correct email address when registering or posting.
SPONSORS

2022 ICRBE
EXPO ON FACEBOOK
CCS Database
Int. Custom Rod Symbol
Common Cents Info
American Tackle
Anglers Rsrc - Fuji
BatsonRainshadowALPS
BRC Rods
Banana River Rods
Cork Specialties LLC
CRB
HNL Rod Blanks–CTS
CTS New Zealand
Custom Fly Grips LLC
Decal Connection
Flex Coat Co.
HFF Custom Rods
HYDRA
Janns Netcraft
Lucas Mfg Co.
Mickel's Custom Rods
My Rod Shop
Mudhole Custom Tackle
MHX Rod Blanks
North Fork Composites
ProProducts
REC Components
ReelSeatBlanks.com
Renzetti Inc.
Rod Builders Warehouse
RodHouse France
RodMaker Magazine
RodMaker Blog
Schneiders Rod Shop
SeaGuide Corp.
Struble Mfg.
Tackleworks
The Rod Room
Trondak U-40
Utmost Enterprises
VooDoo Rods
ZipCast

RX10 Correction
Posted by: Michael Danek (---.alma.mi.frontiernet.net)
Date: July 06, 2021 09:34PM

I cannot find the string of posts in which I mentioned that my Rainshadow Eternity RX10 EFES72MF weighed 1.55 oz, but I correct that post with its re-checked weight of 1.7 oz, (two different electronic scales) which is essentially what the specs say it should be. My first reading must have had the blank "leaning" on something. The CCS data remains, with multiple rechecks, quite different from the specs with power over 500 grams and AA 80. It seems like a great blank, but faster and more powerful than the specs. In the past I have correlated well with both Rainshadow and Anglers Resource. I would be interested in the data from others and from rechecks from Rainshadow.

Options: ReplyQuote
Re: RX10 Correction
Posted by: Batson Enterprises (---.wavecable.com)
Date: July 07, 2021 01:31PM

Hi Michael,
I assume you're referring to model ETES72M-SS. I double checked the measurement on that model and immediately found a problem. The forward brace location mark was an inch too close to the butt (should be at 10% of blank's length) which would cause a lighter IP measurement and a slower AA. After that issue was corrected my numbers came out as: IP 477 and AA 78. This still doesn't match your measurements exactly, but that's what our measurement setup produced. Causes of the discrepancy may be caused by one of the following: our rod fixture does allow the blank to roll to its weakest orientation, and/or there is some variation in how much tip section is used to measure AA. I tend to use about 2 inches of tip section. If you were to look at only an inch it may speed up the AA measurement, but I find in makes it more difficult to see. Just my guesses. -Geoff

-The Batson TEAM
www.batsonenterprises.com

Options: ReplyQuote
Re: RX10 Correction
Posted by: Michael Danek (---.alma.mi.frontiernet.net)
Date: July 07, 2021 03:59PM

Geoff-Thank you very much for your input. I'm essentially getting the same numbers you are with the orientation of the blank so that it's being loaded in its weakest orientation, although there doesn't seem to be much difference in the numbers with other orientations. I'm getting 485-79. 78-79-80 AA is much more representative of this blank than 75, IMHO. This is going to be a very interesting build.

I think I know where my error came in. With its power, and with it's very fast/soft tip, the tip is essentially out of the game as the tip gets close to the 1/3 the length deflection, so any error in measuring the loaded dimension results in significant weight difference. I think I screwed up on that measurement.

My angle indicator is within 3/8 inch of the tip, right against a tiptop, and is fastened with standard masking tape, probably about 5/8 inch. I use an electronic level/angle indicator, so I expect I'm accurate there within a degree.

May I ask another question: Does the orientation of the label mean anything relative to the spline? And I would like to comment that labels placed where you and others put them have to come off when doing most split grips. I think the only solution is to make the labels shorter, about 1 1/2 inch and located right at the butt.

Options: ReplyQuote


Sorry, only registered users may post in this forum.
Webmaster