SPONSORS
2024 ICRBE EXPO |
Spinning guides
Posted by:
John Duncan
(---.lightspeed.jcvlfl.sbcglobal.net)
Date: December 13, 2019 07:27AM
What the purpose of using a taller guide rather than a normal spin cast guide .
Fishing for 50 years and I don’t think I ever saw a “tall “ guide till I started building rods Thanks John d Re: Spinning guides
Posted by:
Dondi Rogers
(---.midsouth.biz.rr.com)
Date: December 13, 2019 09:28AM
The purpose of the taller guide on spinning rods is to compensate for the offset of the reel. Casting reels are basically flush mounted once the foot is inserted into the reel seat. The spinning reel is offset by approximately 2.75". Edited 1 time(s). Last edit at 12/13/2019 09:28AM by Dondi Rogers. Re: Spinning guides
Posted by:
Tom Kirkman
(Moderator)
Date: December 13, 2019 11:13AM
The first spinning guides weren't "tall" but they were large. Over time, manufacturers learned that greater height, more than large ring size, was better for facilitating spinning rod casting qualities. Advances in line technology have also negated the need for overly large rings, but still require some height on the first few guides to get the best casting qualities.
If you put a spinning rod on a casting rod with low guides, it'll cast, but you'll get a lot of line slap on the rod blank in front of that first guide. Again, it'll work, but not nearly as well as rods crafted expressly for use with a spinning reel will. ........... Re: Spinning guides
Posted by:
John Duncan
(---.lightspeed.jcvlfl.sbcglobal.net)
Date: December 13, 2019 11:39AM
Thanks
That’s good information I see now I may need to match the reel up more closely to the guide and it’s location John d Re: Spinning guides
Posted by:
Norman Miller
(---)
Date: December 13, 2019 11:52AM
The modern high frame smaller ring spinning guides have been shown to better control and choke the line coils coming from the spinning reel. This helps to eliminate line slap friction and thus results in longer and smoother casts. Also by reducing the ring size of the guide while maintaining height helps to decrease the overall weight of the reduction train guides. High frame small ring guides, such as match guides, have been around for a long time, however the relatively recent development of the KR concept has greatly increased their popularly. They really do work well.
Norm Re: Spinning guides
Posted by:
Lance Schreckenbach
(---.lightspeed.hstntx.sbcglobal.net)
Date: December 13, 2019 12:57PM
They also help keep the line straight coming from the reel to the choke point of the rod. It will cast better. Before, as stated earlier, a larger ring that had greater height was used but the problem was the continuation of the wave in the line down to almost the tip top. By eliminating the wave closer to the reel, by using smaller guides after the stripper, the rods performance is greatly increased as well as casting distance. Re: Spinning guides
Posted by:
ben belote
(---.zoominternet.net)
Date: December 13, 2019 12:59PM
the super braids have a great deal to do with it..i for years only used spinning for light line fishing but now with the thinner and stronger braids use spinning almost for all fishing..flipping and pitching is still done with casters but i,m sure it can be done with heavier spinning gear.. Re: Spinning guides
Posted by:
roger wilson
(---)
Date: December 13, 2019 01:35PM
John,
For years, I have built all of my spinning rods, so that the first guide is essentially the same height as the center of the spinning reel spool. Over time I have found that if the first guide had the center of the guide in line with the center of the line spool, it eliminates line slap in virtually all of the cases. Then, a quick reduction to a smaller guide and then to running guides make for an excellent spinning rod guide train. True for both mono and braid. Take care Re: Spinning guides
Posted by:
John Duncan
(---.lightspeed.jcvlfl.sbcglobal.net)
Date: December 13, 2019 08:58PM
Again thanks to everyone !
I need to revisit my builds and try out the taller guides John’s Re: Spinning guides
Posted by:
David Baylor
(---)
Date: December 14, 2019 08:13PM
Admittedly I know very little about spinning rod guide trains. What I do know is the weight savings one gets using a KR Concept guide train versus an NGC (new guide concept) or a COF (cone of flight) guide train.
I recently R&R'd an old 6'6" Sjhimano Scabard spinning rod that was advertised as using "Fuji concept guides." The age of the rod leads me to believe that it was an NGC guide train. I weighed the guides I took off that rod. 5 guides plus the tip top, weighed 11 grams. I put Pac Bay Minima guides that are appropriate for a KR Concept guide train. 10 guides plus the tip top, weighed 4 grams. That's a weight savings of 1/4 oz. 1/4 oz doesn't seem like much in the grand scheme of things, but when it comes off the guide train it makes a world of difference in how the rod feels in hand. The balance of the rod changed drastically. The rod casts infinitely better than when it was stock, and is noticeably more sensitive. Re: Spinning guides
Posted by:
roger wilson
(---)
Date: December 15, 2019 08:43AM
John,
Remember, when you speak of taller spinning guides, the only guide that really needs to be taller is the stripper guide so that the eye of the guide is more nearly centered with the center of the reel spool. And in todays world, you really only need ore or perhaps two reduction guides before you get to the running guides to the tip top of the rod. Many folks today use one taller stripper, one reduction guide and then runners to the tip of the rod. Your choice. Re: Spinning guides
Posted by:
Jean Scurtu
(---.hsd1.tx.comcast.net)
Date: December 16, 2019 01:27AM
I like very much the SIC MATCH GUIDES for my spinning rods. My spinning rods are over 10 feet.I don't fish with shorter rods. Sorry, only registered users may post in this forum.
|