SPONSORS
2024 ICRBE EXPO |
Self-centering cork boring jig
Posted by:
Bill Marchisella
(---.nycmny.fios.verizon.net)
Date: August 28, 2019 01:46PM
Can somebody please tell me what volume of RodMaker magazine features how to make this jig or where to buy one?
Thanks for any help. Re: Self-centering cork boring jig
Posted by:
Robert A. Guist
(---.triad.rr.com)
Date: August 28, 2019 03:29PM
Hello Bill.
I lost almost all my mags in Florance but I think it is in 8-5 page 30. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Re: Self-centering cork boring jig
Posted by:
Roger Templon
(---.paw.cpe.atlanticbb.net)
Date: August 28, 2019 03:32PM
Bill
Volume 21, Issue 5 Rog Re: Self-centering cork boring jig
Posted by:
Robert A. Guist
(---.triad.rr.com)
Date: August 28, 2019 04:07PM
Hello Bill & Roger.
Bill; Sorry wrong jig, that one is for cutting thin cork rings. Roger, thanks, I don't have that one. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Re: Self-centering cork boring jig
Posted by:
Tom Kirkman
(Moderator)
Date: August 28, 2019 05:29PM
Volume 1 #3, I think. Sold out a long, long time ago. I have had my eye out for one in case I might run across one but no luck so far.
............ Re: Self-centering cork boring jig
Posted by:
Bill Marchisella
(---.nycmny.fios.verizon.net)
Date: August 28, 2019 08:07PM
I am not sure I have that issue. I will check tomorrow.
Thank you all Re: Self-centering cork boring jig
Posted by:
John Cates
(---.austin.res.rr.com)
Date: August 29, 2019 10:46AM
Flex Coat Pilot Bits
Flex Coat Reverse Pilot Bits [flexcoat.com] [flexcoat.com] [flexcoat.com] Flex Coat Company Professional Rod Building Supplies www.flexcoat.com Re: Self-centering cork boring jig
Posted by:
Robert A. Guist
(---.triad.rr.com)
Date: August 29, 2019 10:49AM
Hello All.
Tom, 1-3 has the jig pictured on the cover but not the one with the article in it, I went thru all my mag's I have left page by page and the article with the plans are not in any of them. The ones I still have are: 1-3, 2-1, 2-2, 2-5, 3-2, 4-2, 4-3, 4-5, 5-2, 5-4, 5-5, 5-6, 6-1, 6-2, 6-3, 6-4, 6-6, All the 7's and 8's, 9-1, 9-3. There is an advertisement in 6-1 p.-8 from "Lanar Reel Seats" from Texas selling them. There is a basic description of it in 9-1 p.-18 (Very Basic). I don't have 21-5, but Roger says its in there, but I'm pretty sure I've seen it in the older magazines. I still have to go through my CD's but I'm still looking. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Re: Self-centering cork boring jig
Posted by:
Tom Kirkman
(Moderator)
Date: August 29, 2019 12:01PM
There are some simple hand clamps in 21-5, but those aren't self centering (although aren't hard to center by hand). Andy Dear began building some of my self centering clamp/jigs after he saw plans. I remember publishing them but not sure what issue they were in. It would also have been pretty early on.
............. Re: Self-centering cork boring jig
Posted by:
Bill Marchisella
(---.nycmny.fios.verizon.net)
Date: August 29, 2019 12:02PM
Robert, you're right. volume 1 issue 3 has no article or plans, just a photo on the cover.I will check the other issues you suggested..I think I can work from a photo to make this jig but would have preferred plans.Tom, if you're still interested in volume 1 issue 3 I have two and I will send you one if you want.
Thanks Re: Self-centering cork boring jig
Posted by:
Tom Harder
(---.hsd1.mn.comcast.net)
Date: August 29, 2019 12:18PM
It's in the "Special Edition * Tools, Fixtures & Shops" CD. I think that is a special edition magazine as well and the self centering cork boring jig is right on the cover. It's Special Edition #3. Edited 1 time(s). Last edit at 08/29/2019 12:22PM by Tom Harder. Re: Self-centering cork boring jig
Posted by:
Robert A. Guist
(---.triad.rr.com)
Date: August 29, 2019 01:06PM
Hello All.
I fell like a dummy just got done with my CD's and Tom H. is right it is in the SE "Tools, Fixtures & Shops", last one page 100-106, I Think. I still think I saw it in one of my old magazines, but I lost so many. PS Tom K. It looks like I will make it to the next EXPO. Will you have at least 1 of each of the old back magazines? I hope to restore most of my missing magazines. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Edited 1 time(s). Last edit at 08/29/2019 01:10PM by Robert A. Guist. Re: Self-centering cork boring jig
Posted by:
Bill Marchisella
(---.nycmny.fios.verizon.net)
Date: August 29, 2019 01:08PM
Thank you Tom Harder for finding this article, It looks like a good CD to have. I think this article is in RodMaker magazine somewhere because it said that this CD was compiled from articles from the magazine I could swear I saw it. Most likely I'll buy the CD. Re: Self-centering cork boring jig
Posted by:
Bill Marchisella
(---.nycmny.fios.verizon.net)
Date: August 29, 2019 01:08PM
Thank you Tom Harder for finding this article, It looks like a good CD to have. I think this article is in RodMaker magazine somewhere because it said that this CD was compiled from articles from the magazine I could swear I saw it. Most likely I'll buy the CD. Sorry, only registered users may post in this forum.
|