SPONSORS
2024 ICRBE EXPO |
microwave guide setup.
Posted by:
scott south
(---.static.bresnan.net)
Date: March 01, 2018 10:43PM
First time poster here..I'm building a nfc jig rod and need some help setting up my microwave guides.The rod I am building a 5 foot 9 inch rod,I remember seeing a post on this forum indicating the setup for a 6 foot rod .Just wondering if the would be same for both rods? Re: microwave guide setup.
Posted by:
Lou Auret
(204.16.161.---)
Date: March 02, 2018 07:53AM
Do setup from face of reel going towards tip
Those first three guides are critical for easy casting with a microwave setup. Then working froward I would use the same setup as for 6 ft but drop the last guide near tip as that is at around 3 inches from tip so would not be required. Of course this assumes your butt section/reel seat location is as long as the 6ft you are trying to copy. tape it up and test cast. Each blank is different so you always need to do that. Re: microwave guide setup.
Posted by:
Michael Danek
(---.alma.mi.frontiernet.net)
Date: March 02, 2018 08:58AM
The first three guides go right where the little paper that comes with the guides says they go, then place the others where it makes sense using a stress test to place them. You probably will have at least one, maybe two running guides left over since the rod is so short. Test cast, but you most likely will have to move nothing.
Read the "static guide placement" article in the library, but place the first three guides where American Tackle instructions (the little paper) say. Re: microwave guide setup.
Posted by:
Robert A. Guist
(---.dhcp.embarqhsd.net)
Date: March 02, 2018 10:17AM
Hello Scott.
I do it the same as Michael. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Re: microwave guide setup.
Posted by:
David Miller
(---.pools.spcsdns.net)
Date: March 02, 2018 12:26PM
Agree with all said, one thing to add, check out nfc website guide spacing chart for your blank to get the spacing close to ideal for the running guides. Edited 1 time(s). Last edit at 03/02/2018 02:55PM by David Miller. Re: microwave guide setup.
Posted by:
Don @ American Tackle
(---.biz.bhn.net)
Date: March 02, 2018 01:59PM
I was going to jump in but these guys took great care of you... if you have any questions about MicroWave or anything AT, please do not hesitate to give me a call. _______________________________ God Bless, Don Morse 800-516-1750 ext. 1207 / don@americantackle.us Rod Building..... It's What We Do. Re: microwave guide setup.
Posted by:
Phil Ewanicki
(---.res.bhn.net)
Date: March 02, 2018 05:59PM
Is the difference between spacing guides dependent upon their inside diameter, outside diameter, flexibility, height above the blank, guide ring material, or advertising? Does the blank being used, the type of line being used , its diameter or flexibility, or the ambient temperature where the guides/rod are used influence guide spacing? It seems pretty complicated! Re: microwave guide setup.
Posted by:
Michael Danek
(---.alma.mi.frontiernet.net)
Date: March 02, 2018 07:16PM
yes. Re: microwave guide setup.
Posted by:
ben belote
(---.zoominternet.net)
Date: March 02, 2018 07:59PM
but Phil, can,t you see that,s why you need a professional rod maker to guide you through all these complications..lol. Re: microwave guide setup.
Posted by:
scott south
(---.static.bresnan.net)
Date: March 02, 2018 10:18PM
Thank you to all who answered my question,I'll start wrapping this rod this weekend,thanks again.
Fish-on! Sorry, only registered users may post in this forum.
|