SPONSORS
2024 ICRBE EXPO |
Rod Tubes for Travel Spinning Rods
Posted by:
Tony Scott
(---.177.90.245.available.above.net)
Date: August 26, 2013 12:53PM
Can anyone recommend rob tubes with dividers built in for 3 pc spinning rods that are 7 feet long? Right now, I am finding Clear Creek and then there is Clear Creek. Re: Rod Tubes for Travel Spinning Rods
Posted by:
Lou Auret
(204.16.161.---)
Date: August 26, 2013 01:38PM
Look at rifle cases.
easier to store(flat) come with foam inside so easy to customize. Price is good too. Re: Rod Tubes for Travel Spinning Rods
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 26, 2013 02:03PM
Anglers Workshop - landmark - alpine Bill - willierods.com Re: Rod Tubes for Travel Spinning Rods
Posted by:
Chris Richer
(131.137.245.---)
Date: August 26, 2013 02:50PM
Build a wooden, octoganal, one like Mark Crouse and a rod sock for a three piece rod. you then get to pick the wood species and finish. Custom :) Chris Richer Iroquois ON Re: Rod Tubes for Travel Spinning Rods
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: August 26, 2013 03:11PM
Tony,
Make it very simple. Take two bread bag twisties, and use the twisties to hold the three rod pieces together. Then, pick up the smallest pvc tube that will accomodate the rod - typically a 2 1/2 inch or a 3 inch tube. Put a PVC cap on each end. Glue one cap on the tube and sand the other end as needed to make the opposite cap removable. The twisties are free and the tube will cost you about $2. Also, this tube will give you the minimum travel space needed for your rod. Be safe Re: Rod Tubes for Travel Spinning Rods
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 26, 2013 03:57PM
And people say I am cheap LOL Bill - willierods.com Re: Rod Tubes for Travel Spinning Rods
Posted by:
Don Morse
(---.dhcp.aldl.mi.charter.com)
Date: August 26, 2013 04:21PM
bill boettcher Wrote:
------------------------------------------------------- > And people say I am cheap LOL You are...LOL.... my wife says I am cheap, I tell her I am frugal. ______________________________________ Super Tight Lines......Don Edited 1 time(s). Last edit at 08/26/2013 04:22PM by Don Morse. Re: Rod Tubes for Travel Spinning Rods
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 26, 2013 04:45PM
Ya but is there not a difference ???LOL
I would have painted the tube and cleared it -- So is that Frugal ?? Bill - willierods.com Re: Rod Tubes for Travel Spinning Rods
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: August 26, 2013 05:52PM
I am sure that everyone has some beautiful decal's to put on the tube.
Simply put, a simple PVC tube is much more practical than any sort of box. Also, it is much more compact and stronger. I have an industrial sewing machine and make a lot of things on it. One of the things that I make for myself are rod traveling sacks. I used to carry a large 4 inch tubes to take the dozen or so rods that I normally take on a trip. But, I found that it was always bulky and in the way and it would roll around. Since I did not need the protection of the tube - with the rods on top of all of the other luggage, I found it easier to make about a 3-4 inch diameter sack 8 feet long that takes care of all of my rod carrying needs. Be safe Re: Rod Tubes for Travel Spinning Rods
Posted by:
Lance Dupre
(---.lightspeed.nworla.sbcglobal.net)
Date: August 26, 2013 06:12PM
I'd like to know where to get a PVC tube for 2.00. A four foot cut off sells for 5.00 to 6.00 at my local Lowes and Home Depot. Re: Rod Tubes for Travel Spinning Rods
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: August 26, 2013 06:19PM
Swampland.
Buy a 10 foot tube and then chop it to length. [www.lowes.com] The 10 footer is $7.50 and for a three piece travel tube, should be able to chop it in 3rds for $2.15 each. Be safe Re: Rod Tubes for Travel Spinning Rods
Posted by:
Jim Gamble
(---.res.bhn.net)
Date: August 27, 2013 04:44PM
St Croix offers a wide variety of very nice tubes. Re: Rod Tubes for Travel Spinning Rods
Posted by:
Tony Scott
(---.177.90.245.available.above.net)
Date: August 29, 2013 12:46PM
Thanks to all who replied.
I ended up ordering some custom length tubes with dividers from Clear Creek. They asjed me for length of the longest section and I did not realize how much difference there can be between sections on a spinning or casting rod. I have not found that with fly rod blanks. Sorry, only registered users may post in this forum.
|