SPONSORS
2024 ICRBE EXPO |
Thread Master
Posted by:
Bill Cohen
(---.dhcp.embarqhsd.net)
Date: December 03, 2012 12:27PM
Have a lot of the high build TM.Am not pleased with my wrapes think they are too bulky.I was wondering if anyone has added acetone to the Thread Master to thin it down. Ive done the drill not using lots of TM. always turn the rod by hand letting excess accumulate,and remove. Still not satisfied. If some one has used acetone what part acetone to TM. Re: Thread Master
Posted by:
Tom Kirkman
(Moderator)
Date: December 03, 2012 12:54PM
Don't let excess accumulate. Don't apply any excess. Use a stiffer brush and simply put on less.
......... Re: Thread Master
Posted by:
Phil Erickson
(---.dsl.pltn13.sbcglobal.net)
Date: December 03, 2012 12:54PM
I have used DNA successfully to thin TM. Keep in mind that when you add something to the epoxy, you will change it's curing time. In the case of the DNA it slowed the TM appreciably. Re: Thread Master
Posted by:
lorenzo tellez
(---.hsd1.il.comcast.net)
Date: December 03, 2012 01:13PM
Hello Maryann, If you want to get rid of some I am always looking for a deal,lol! Now that I am getting a whole lot better on applying epoxy high or lite formula, just let me know in an email good luck! Re: Thread Master
Posted by:
Capt. Craig Freeman
(38.127.195.---)
Date: December 03, 2012 01:27PM
Switch to TM lite. Re: Thread Master
Posted by:
Jeff Shafer
(---.mycingular.net)
Date: December 03, 2012 04:10PM
I've been down the high build vs lite formula road a few times. In my experience lite formulas tend to migrate to the centers of my wraps as gravity does its thing. This seems to occur no matter how little epoxy I apply. I've found that my wrap finishes end up more level using high build formulas. It is possible to apply three coats of high build epoxy and obtain a thin, delicate looking finish - if you read Tom's post carefully.
Jeff Re: Thread Master
Posted by:
Col Chaseling
(---.lnse1.cht.bigpond.net.au)
Date: December 03, 2012 04:54PM
Hi Maryann,
I've been using Threadmaster high build for a few years and think it's a good finish and it doesn't appear bulky to me and I usually use two coats like this one [www.rodbuilding.org]. I think you should do several test wraps on a scrap piece and do some experimenting with your finish application. Sounds like you are using way too much. ESFNEM Col Port Kembla, NSW Australia Re: Thread Master
Posted by:
Terry Turner
(---.hsd1.or.comcast.net)
Date: December 04, 2012 01:06PM
Hmmm. I read these finish posts and wonder what folks are doing. I'm a threadmaster light guy, and make successful, level finishes almost every time, almost always in 1 coat. I occasionally need to touch up so if I err, it's on the too little side.
I use a spatula, not a brush, but I think good techniques can be had with both methods. The amount applied is pretty critical. Too much and it balls up on the guides, or becomes wavy on the butt wrap finish. Apply and leave it. 10-20 seconds per wrap max. I rotate my rod on the wrapper by hand to apply. A fast spin on the edges for a clean line, then a couple of turns to fill in the middle with a loaded spatula. Set it on the dryer and go do something else. Hope this helps but I know finish can be affected by temp and humidity as well as the application methods. I think Tom and others have suggested trying several brands to see which best fits your style. I like the TM lite results but wish it cured a little faster. Terry Sorry, only registered users may post in this forum.
|