SPONSORS
2024 ICRBE EXPO |
lathe tool storage ideas
Posted by:
Walt Davenport
(63.97.59.---)
Date: April 14, 2011 12:28PM
I could use some suggestions for lathe tool storage for my new jet mini with extended bed on jet stand. I've gone from an old lathe mounted to a bench where I had everything handy to this and now could use some ideas to get me organized and keep my tools close.
Thanks for any suggestions. Walt Davenport "Roadhouse Rods" Re: lathe tool storage ideas
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: April 14, 2011 01:08PM
Walt,
A rubbermaid container works just fine. Roger Re: lathe tool storage ideas
Posted by:
Chuck Mills
(---.grenergy.com)
Date: April 14, 2011 01:08PM
I just keep mine under a pile of cork dust and sandpaper scraps.
Thanks starting this topic, Walt. I will be watching for ideas, because I need them! _________________________________________ "Angling is extremely time consuming. That's sort of the whole point." - Thomas McGuane Re: lathe tool storage ideas
Posted by:
Walt Natzke
(170.146.227.---)
Date: April 14, 2011 02:20PM
Chuck Mills Wrote:
------------------------------------------------------- > I just keep mine under a pile of cork dust and > sandpaper scraps. > LOL, Chuck, that is where I keep MOST of my tools! Walt Natzke Ripon, CA Re: lathe tool storage ideas
Posted by:
john timberlake
(---.triad.res.rr.com)
Date: April 14, 2011 02:56PM
take a look at the new trex tool caddy offered by woodturners catalog..it will give you some great ideas..i also use pvc for mandrels and such and have a magnetic tool holder on the wall for the most frequently used lathe tools Re: lathe tool storage ideas
Posted by:
Rena Hall
(---.oc.oc.cox.net)
Date: April 14, 2011 05:49PM
Walt,
I use Walmart's Modular plastic Drawers. You can see dozens of different sizes at this link: [www.walmart.com] Rena Re: lathe tool storage ideas
Posted by:
Bill Ballou
(---.hsd1.tn.comcast.net)
Date: April 14, 2011 08:02PM
H. Freight & N.Tools have magnetic strips. Have some on wall behind lathe Re: lathe tool storage ideas
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: April 14, 2011 08:45PM
Walt,
Rather than leaving the tools out in the open - subject to rust and moisture, I find that keeping the tools, chuck etc. etc. in a closed up box really helps to keep all of the tools clean, free of corrosion etc. that can be rather common in some work place environments. That is the reason that I suggested the use of a rubbermaid or similar box. When working on a job, take the two or three tools out that you need for the job, and then close th box back up. That keeps the dust, dirt and moisture out of the unused tools. Here in the midwest, especially when coming out of the winter season, unless a person takes special pains, tools that have been left in unheated, or only seldom heated work spaces and subject to a great deal of condensation, can have some big rusting issues, come spring. I would think that on the humid parts of the east coast, one might have similar issues. Of course the optimum is 24 hour by 365 constant humidity and temperature to avoid these issues. Be safe and enjoy your lathe. It is a very good one. Roger Re: lathe tool storage ideas
Posted by:
Mike Barkley
(---.nap.wideopenwest.com)
Date: April 14, 2011 09:38PM
Take a piece of wood (about 1" x 3") whatever length you need and use a Forstner bit of the correct size to put holes that will allow your turning tools to hang through to the handle with the ferrule fitting snug enough to hold the tools upright and leaving the tool itself visible for easy selection.. Mount the board anywhere that's convenient.
Simple, quick and convenient. Mike (Southgate, MI) If I don't want to, I don't have to and nobody can make me (except my wife) cuz I'm RETIRED!! Re: lathe tool storage ideas
Posted by:
Walt Davenport
(---.hr.hr.cox.net)
Date: April 17, 2011 10:50AM
Some good ideas here, I think I'll probably make a small shelf on the bottom rail of the stand and secure a few rubbermaid drawers to it and also add a couple magnetic strips within reach.
Thanks for the suggestions! Walt Davenport "Roadhouse Rods" Re: lathe tool storage ideas
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: April 18, 2011 05:11PM
Walt,
One other thing that may or may not have been mentioned. If you like, and especially if you have handles that are all the same size on your lathe tools - find a pvc pipe that will give the handles a nice fit. Then, take a nice board that is a bit wider than the diameter of the pvc pips. Figure how many tools you need to store. Then, take a fostner bit, or an adjustable hole cutting bit - do some test drilling on a piece of scrap, until you have a hole size that give the pvc pipe a tap in fit into the board. Then, use an abrasive wheel, or chop saw with an abrasive wheel in it to cu tthe pvc tubes to the lengths of the handle minus about 1/2 inch or so. The idea is that you will store the lathe tools upside down by the handles being dropped into the pvc tubes. You can drill the board so that you have about 1/4 inch space between the outside edges of the pvc pipes. When done drilling the holes, take a drill and drill a couple of holes through the width of the mounting board. Now, take your trimmed pvc pipes and tap them into the holes in the board that are a tight fit for the pipes. Finally, use a couple of long screws to mount the board to the side of your work bench or table or wall. Now, just drop the lathe tools into the pipes upside down, and you can see at a glance the tool that you want to use. Many lathe tools have a tool cutting width that is smaller than the width of the handle. So, that is why I will often make a holder that supports the tool by the handle. If you have a matched set of tools, then the handles will be the same. I tend to dislike the use of magnetic tool holders because they will slip now and then, but the biggest reason is that magnetic tool holders will magnetize the tools. If you work with magnetized tools, any ferros metallic tool shavings that are laying around the area will be attracted to the tools and can sometimes get in the way. Take care and be safe Roger Sorry, only registered users may post in this forum.
|