SPONSORS
2024 ICRBE EXPO |
Brother PTouch for Rod Decals
Posted by:
Steven Tekulsky
(---.nycmny.east.verizon.net)
Date: February 15, 2011 01:46PM
Anyone use a Brother P Touch label maker for rod decals? Does it work? Re: Brother PTouch for Rod Decals
Posted by:
John M. Hernandez
(---.socal.res.rr.com)
Date: February 15, 2011 01:53PM
Yes it does. You want to use Testors clear enamel to seal the edges because they have a tenency to lift very easily. What I do is apply the decal wrap over it and leave it over night. The next day I remove the wrap and apply the clear enamel let it dry for about an hour and you are good to go.
Tight lines, John Re: Brother PTouch for Rod Decals
Posted by:
Steven Tekulsky
(---.nycmny.east.verizon.net)
Date: February 15, 2011 01:57PM
Thanks John..............I'm assuming they make a clear tape with different colors for the print? Going to go over a darker rod............ Re: Brother PTouch for Rod Decals
Posted by:
Bert Nagy
(---.asm.bellsouth.net)
Date: February 15, 2011 02:40PM
I use a P Touch 2300. It works very well for me. I use white print on a clear label. The only place I could find the tape was through Brother.
Mine hooks up to my computer via USB, and that gives you a lot a flexibility with respect to fonts, layouts, etc. You can even put in graphics. I have not had a problem with the edges lifting, as John mentioned. I put the label on the on the blank and wrap the ends with thread as trim bands. I then put thread epoxy over l the entire label and thread. The only thing that I wish was better, was you can see the edge of the label. It is somewhat distinct. Regards Bert Nagy Re: Brother PTouch for Rod Decals
Posted by:
Steven Tekulsky
(---.nycmny.east.verizon.net)
Date: February 15, 2011 02:49PM
Thanks, Bert.......would love to see a picture of how it looks, if possible. Re: Brother PTouch for Rod Decals
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: February 15, 2011 03:50PM
Decal Connection will make you ( 1 ) decal if you need that Cheap, easy and very good quality. Bill - willierods.com Re: Brother PTouch for Rod Decals
Posted by:
Bert Nagy
(---.asm.bellsouth.net)
Date: February 15, 2011 06:24PM
Steven,
Your email is hidden. If you send me an email, I will send you a picture or two. Regards Bert Nagy Re: Brother PTouch for Rod Decals
Posted by:
Brad Young
(65.244.135.---)
Date: February 16, 2011 11:49AM
I have used these labels for a while. The problem with the edges lifted is very great with mine. I am using the 1/2 tape white on clear. I have found that I need to use perma seal or perma gloss over the edges and let it dry. Then apply finish. sometimes they still tend to lift. Re: Brother PTouch for Rod Decals
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: February 16, 2011 02:11PM
CP will not work on these ??? Bill - willierods.com Re: Brother PTouch for Rod Decals
Posted by:
Brandan Martin
(---.lightspeed.chtgtn.sbcglobal.net)
Date: February 19, 2011 05:39PM
I used their colored tape for a few years. My issue is when I see one of those old rods, the text has faded so badly that it looks awful. I started using Decal Connection and it is worth the time and cost for me. I did buy the paper that has been sold at the show over the past few years and it works great. I just need some to do the layout for me. If the clear tape is the difference, please let me know. The colored tape that has stayed out of the sun is fine but the rods that really get used look bad. Sorry, only registered users may post in this forum.
|