SPONSORS
2024 ICRBE EXPO |
Renzetti lathe drive belt
Posted by:
Michael Mayo
(---.dyn.optonline.net)
Date: February 11, 2010 10:46PM
I have a Renzetti Rod lathe and I just ordered the newer motor and foot pedal setup. Man do they charge a ton of money for this stuff. Everything Renzetti sells cost a fortune????? Anyway I forgot to order another drivebelt at the same time....DUH! So I was wondering if anyone here has found an alternate cheap source for the mini V-belt that is used on the Renzetti Lathe. I have searched around the net looking but without a size or manufacturer # it is impossible to tell what exactly I need. Thanks for any help you folks might be able to share. Michael Mayo Senior IT Support Engineer Milford, CT. "I work so I can Fish" Re: Renzetti lathe drive belt
Posted by:
Tom Kelly
(---.sd.sd.cox.net)
Date: February 12, 2010 12:17AM
Michael, my Renzetti belt is a "Gates 3M315"... and there are a number of sources online from which you can buy them. Re: Renzetti lathe drive belt
Posted by:
Michael Mayo
(---.dyn.optonline.net)
Date: February 12, 2010 08:01AM
Tom Kelly Wrote:
------------------------------------------------------- > Michael, my Renzetti belt is a "Gates 3M315"... > and there are a number of sources online from > which you can buy them. Thank you Tom the letters are all worn off on mine much appreciated. Michael Mayo Senior IT Support Engineer Milford, CT. "I work so I can Fish" Re: Renzetti lathe drive belt
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: February 12, 2010 10:05AM
Michael,
I have no idea what you had to pay for a foot pedal. But if you want to go right to the source in the future, go to Linemaster.com and order the replacement pedal directly from the manufacurer. These are very high quality industrial pedals that will last many many years. [linemaster.com] From their web site- you can find your nearest local distributor, of if you need to; you can order directly from the manufacturer. For the motor, you can go directly to Graingers.com and place an order for your replacement motor. Take care Roger Re: Renzetti lathe drive belt
Posted by:
Michael Mayo
(---.dyn.optonline.net)
Date: February 12, 2010 06:23PM
roger wilson Wrote:
------------------------------------------------------- > Michael, > I have no idea what you had to pay for a foot > pedal. > But if you want to go right to the source in the > future, go to Linemaster.com and order the > replacement pedal directly from the manufacurer. > > These are very high quality industrial pedals that > will last many many years. > > [linemaster.com] > atNo=ACVariableSpeedControl > Roger, I have the original design pedal with motor assy. the pedal is perfectly fine but without the A/C adapter which stopped functioning it is no longer of any use as they no longer use the older motor design and pedal. So I had to purchase the newer Dayton motor and solid state pedal through Renzetti. If I could of gotten the adapter from linemaster I am going to be seriously perturbed. Although I think the newer design motor and pedal will hopefully be better than the old design. We will see. > From their web site- you can find your nearest > local distributor, of if you need to; you can > order directly from the manufacturer. > > For the motor, you can go directly to > Graingers.com and place an order for your > replacement motor. > > Take care > Roger Michael Mayo Senior IT Support Engineer Milford, CT. "I work so I can Fish" Re: Renzetti lathe drive belt
Posted by:
Michael Mayo
(---.dyn.optonline.net)
Date: February 12, 2010 06:28PM
It looks like Linemaster only covers the pedals and they are the same as the newer designed one I ordered from Renzetti. My older designed motor and pedal didn't interface the same as these newer ones. There was a seperate plug for the pedal which plugged directly into the motor housing and then another receptacle that you plugged the small A/C adapter into. The motor housing has a rheostat on the front and a switch that allowed you to use either the foot switch or the rheostat to control speed of the lathe. Very old model lathe but the bed and uprights are the same as the current ones. as well as the headstock. Michael Mayo Senior IT Support Engineer Milford, CT. "I work so I can Fish" Re: Renzetti lathe drive belt
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: February 12, 2010 11:24PM
Micachael,
Any of these ac/dc series wound motors that are used to power the typical ac powered rod wrapper can be controlled by any of the readily available electronic or mechanical rheostat style controls. It is a simple matter to change the wiring of any of these lathes if needed. All that you have are two wires going to the motor and possibly switche and or other controls that switch or don't switch contacts or pedals to other uses and or sources. Take care Roger Re: Renzetti lathe drive belt
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: February 12, 2010 11:28PM
p.s.
The controller that is used in todays linemaster variable speed ac controller is nothing more than a nylon base with a nylon foot rest on top of it with an arm on the back of the base. The arm pressess against a variable switch which is nothing more than the typical variable speed ac drill motor controller. Actually, I think that linemaster was quite clever to use this design. There are literally millions of these controllers in use today in the world. Thus the manufacturing cost of these controllers are measured in only a few dollars. Linemaster makes the nylon injection molds for the foot pedal and takes care of the molding. Then, the simple addition of these inexpensive readily available controls make a very very good switch that is available at a very competitive price. Take care Roger Re: Renzetti lathe drive belt
Posted by:
Barry Thomas Sr
(---.hsd1.nj.comcast.net)
Date: February 14, 2010 10:15AM Sorry, only registered users may post in this forum.
|