SPONSORS
2024 ICRBE EXPO |
Static charge in blank
Posted by:
Fred Yarmolowicz
(---.brick101.nj.comcast.net)
Date: January 01, 2006 11:42AM
With the forced hot air heat we utilize here it seems satic build up is in everything including the rod I`m trying to wrap.Remove the dust and it is back in 2 minutes.Sprayed with water to no avail.Finally went upstairs and got out the Static Guarde spray and sprayed the area and the blank.Seems to have worked however the can does not list the contents.Any thoughts as to what may happen??? if anything at all??.I`m going to try the manufactures web site to see if they have a list of chemicals and also warnings.Also what do you do to combat the static charge concern. Freddwhy (Rapt-Ryte) Re: Static charge in blank
Posted by:
bill boettcher
(---.nj-01.cvx.algx.net)
Date: January 01, 2006 12:59PM
Fred
If you can't find the list, may be try a scrap blank. Wrap some thread on, with and with-out the spray, put finish on, and see what happens ?? You can always wash the blank off, but if it is in the air it may give ( fisheyes ) ? Re: Static charge in blank
Posted by:
Fred Yarmolowicz
(---.brick101.nj.comcast.net)
Date: January 01, 2006 02:00PM
looked on the can again and there is only one ingredient,Ethanol.I overlooked that because I was looking for a much longer list. Freddwhy (Rapt-Ryte) Re: Static charge in blank
Posted by:
Jaime Choy
(---.dsl.pltn13.pacbell.net)
Date: January 01, 2006 04:53PM
Fred Yarmolowicz,
Instead of using a spray, I suggest that you buy an Ionizer. Electronic manufacturing suppliers sell them. The Ionizer will neutralize the static electricity easily. Re: Static charge in blank
Posted by:
Randy Parpart (Putter)
(---.propel.com)
Date: January 01, 2006 07:23PM
I have a humidifier in my work room (on low) and I also dip my finger in some water and drip it on the felt of my rod support to keep it from building up static. When putting finish on while the rod is turning, I put a bit more water on that felt area every 20 minutes or so.
I also have an old screen door frame (from one of the screens) that I cut down to size, put a piano hinge on it and also to the wall, and replaced the screen with some tack cloth. After applying the finish, I bring this screen down right over the top of the rod as it's turning. I place another tack cloth over the front edge of this screen frame down to the top of my work bench. Over top of my heater's outlet in my room, I place another tack cloth to keep any airbornes from circulating. During the dry, winter months I used to have tons of troubles until I did these things. It solved it for me, Fred. Putter Williston, ND Re: Static charge in blank
Posted by:
Fred Yarmolowicz
(---.brick101.nj.comcast.net)
Date: January 02, 2006 08:43AM
Come to think of it this rod is in the hand wrapper not on the rollers and it is rolling in felt.I`m sure that dont help the problem.Thanks all.The spay did the trick although I dodt know if there are any finish problems yet. Freddwhy (Rapt-Ryte) Re: Static charge in blank
Posted by:
bill boettcher
(---.nj-01.cvx.algx.net)
Date: January 02, 2006 09:50AM
Hay Putter
have you ever thought of a spray booth ? Maybe just a long box with some ducting attached and a fan going outside ? Could maybe use it as a heating box also ?? Re: Static charge in blank
Posted by:
Anonymous User
(---.ptld.qwest.net)
Date: January 02, 2006 12:35PM
for all of you that are haveing static problems one of the bigest problems is not enough grounding in your home and heating and air conditioning systems code calls for x amount of ground for power bumps, lighting and other reasons. ask any electrical enginer about static more grounding is a big help not a complete cure Re: Static charge in blank
Posted by:
Randy Parpart (Putter)
(---.propel.com)
Date: January 03, 2006 12:23AM
Jeez, I gotta move 1/2 my room around as it is to start new projects; to finish wrapping and begin applying finish is 1/2 hour of work just to prepare the little bench I have, Bill. I just don't have room for any more "STUFF"!! LOL! I know us guys like to have our stuff, but there's only so much I can pack in there! Putter Williston, ND Re: Static charge in blank
Posted by:
Terry Turner
(---.hsd1.or.comcast.net)
Date: January 03, 2006 10:05AM
Fred,
Jamie and Randy got it right. The winter months bring low humidity, and with heating cold outside air and forcing it around the house generates lots of static electricity. This really doesn't have much to do with the grounding in your house as the static is generated by the air movement in combination with the low humidity. You can ionize the air to neutralize the static charge around your work area. This is a common practice in electronics assembly operations where static sensitive devices are used and is done with a benchtop device that costs around $200 to $500. Adding a humidifier in the room or raising the humidity in the way that Randy mentions will also work, in combination with filtering the dust particles as has been discussed in the past. Good luck. Terry Sorry, only registered users may post in this forum.
|