SPONSORS
2024 ICRBE EXPO |
Results 1 - 30 of 40
1 year ago
Bill Break
I fish the Canadian side of Ontario. I built a couple of rods on the Rainshadow RX4 BP 1025 blanks and have been happy with the rods. MHX has a line of rigger rods that are more affordable. As Tom says spiral wrap. I use the slick butts for rear grips with the channel lock reel seats. Also because I fish out of a 18 foot Lund I keep the rods shorter, 7 to 8 1/2 feet.
Forum: rodboard 1 year ago
Bill Break
Thanks. Being a novice builder when I buy nylon I know if I want to keep the color of the thread I need CP. Looking forward to using the threads.
Forum: rodboard 1 year ago
Bill Break
I recently inherited some spools of Gudebrod's champion thread. These are 1 ounce wooded spools that are marked Nylon on one end and stamped NCP on the other end. I am going to test the thread, just wondering why the spools are marked both.
Forum: rodboard 1 year ago
Bill Break
My son was recently given 2 Pezon et Michel 7 foot 4 inch bamboo rods in need of some guide repair. There appears to be varnish on the guide thread as opposed to epoxy. Can I retie and use epoxy on the guides? Also the finish on the rod is worn off in a few places. Is practical to strip and sand the rod and refinish? Thanks for any help.
Forum: rodboard 2 years ago
Bill Break
I built 2 wire dipsy rods on the BP1025 blanks. Spiral wrap with slick butts. The blank loads up perfect.
Forum: rodboard 3 years ago
Bill Break
Would also suggest Rainshadow BP1025F. Going to be my next build for boards.
Forum: rodboard 3 years ago
Bill Break
I built 2 wire dipsy rods last year using Rainshadow SW967F blanks. Would suggest the slick butts also.
Forum: rodboard 3 years ago
Bill Break
Will give that a try. Made a 2 piece block out of hickory with a hole slightly larger than the diameter of the male ferrule . Had the rod flat on a table with the trigger of the reel seat hooked on the end of the table. One person holding the rod down, me pulling on the other end while my son beat on the block . Started to imbed the female end into the hickory block. Have been trying ever sugge
Forum: rodboard 3 years ago
Bill Break
Still working on the rod. Tried the reverse clamp with no success. The rod is a 13 foot Raven float rod in three pieces. It is taken apart every time. My son was fishing the St. Mary's river and the rod got submerged . It has been stuck since.
Forum: rodboard 3 years ago
Bill Break
Thanks for all the help. Have tried every method except the reverse clamp. Just going to keep at it.
Forum: rodboard 3 years ago
Bill Break
It is a black ferrule. I assume some sort of graphite .It is a Raven float rod.
Forum: rodboard 3 years ago
Bill Break
Thanks . The only problem is I live in Canada and the magazines are not available to me.
Forum: rodboard 3 years ago
Bill Break
Tried all solutions offered. Still stuck. The ferrule is 34 inches from the for grip. the next section is 54 inches. how do I go about installing a new ferrule?
Forum: rodboard 3 years ago
Bill Break
17. Stuck ferrule
My son's float rod will not come apart at the first ferrule. I was going to remove the ferrule wrap on the female side and try a bit of heat. Any help would be appreciated .
.
Forum: rodboard 3 years ago
Bill Break
Just built 2 Rain shadow dipsy rods with slick grips. They are great. Going to cut the EVA grips off my remaining down rigger rods this winter and replace them with Slick Grips.
Forum: rodboard 3 years ago
Bill Break
Also, do yourself a favor and use a Slick Grip for the rear. Comes out of the holder much better.
Forum: rodboard 3 years ago
Bill Break
22. Re: Wire Line
The main reason for wire line on Lake Ontario is the water fleas. Braid is fine until the fleas show up as the water warms. They cling to the braid and you end up with pipe cleaner all the way down the line that clogs the tip. Wire line saws right through them.
Forum: rodboard 3 years ago
Bill Break
23. Re: Wire Line
30 pound stainless 7 strand wire line. Used to connect to a dipsy diver.
Forum: rodboard 3 years ago
Bill Break
24. Re: Wire Line
I just built two Rain Shadow blanks using the silicon nitride guides in spiral wrap with slick grips for wire line on Lake Ontario. Still on lock down on the Canadian side, can't get out to try them.
Forum: rodboard 4 years ago
Bill Break
26. Rod Builders CD
This a request for Tom Kirkman. What is the delivery time for a cd? I live in Canada and have a friend in Gulfport MS until the end of Feb. Would This time frame be possible? I emailed the magazine site but have not had a reply. Thanks
Forum: rodboard 4 years ago
Bill Break
27. Magnifier
I am in need of a magnifier for my old eyes. Just looking for some input on the use of table top magnifiers or the head mounted.
Forum: rodboard 4 years ago
Bill Break
Thanks. I have a set of cork reamers. Just didn't know if you could ream the EVA.
Forum: rodboard 4 years ago
Bill Break
Building a rod with a butt diameter of .680 . Should I use the eva rear grip with the bore diameter of half inch or the five eights? Thanks
Forum: rodboard |