SPONSORS
2024 ICRBE EXPO |
Results 1 - 30 of 42
9 months ago
Tony Papazian
Thanks for all the info guys! I have a couple swimbait rods I really like that I was hoping to be able to get the blanks & make them collapsible rods but, it looks like the best route is to try to find comparable rod blanks that are already made to collapse.
Forum: rodboard 9 months ago
Tony Papazian
Due to room in my rod locker & front deck I would like to build some rods with a collapsible but section like the old style flipping stick. How do I do this with blanks being one piece? Do I cut the blank at the point I want it to collapse & run the top part of the blank up through the bottom of the butt section? Any help would be appreciated.
Thanks,
Tony
Forum: rodboard 10 months ago
Tony Papazian
Norman Miller Wrote:
-------------------------------------------------------
> I’ve built several X-ray Neo MB765 as KR casting
> rods. For fresh water use, I use the corrosion
> control stainless guides. I use a KW10 butt guide
> followed by a KW5.5, then three KB5s and five KT5s
> as runners for a total of ten guides. The tip top
> was a matching LG tip top. For salt wa
Forum: rodboard 10 months ago
Tony Papazian
Thanks everyone. I will be using this with 14-20lb Fluorocarbon.
Forum: rodboard 10 months ago
Tony Papazian
Can anyone point me in the right direction on what size guides to use on a NFC MB 765-1(X-Ray NEO) blank?
Forum: rodboard 10 months ago
Tony Papazian
Spinning for sure unless you get into the BFS casting reels.
Forum: rodboard 10 months ago
Tony Papazian
I've built several spinning rods & I'm getting ready to build my first casting rod. I've used the KR guides for my spinning rods & they have a nifty little calculator to help choose your guides & guide sizes. Is there anything like that for casting rods or is there some kind of chart that can help me choose the right guides?
Thanks,
Tony
Forum: rodboard 3 years ago
Tony Papazian
10. Guide Setup 3
<p>Do I need to add one more guide?</p>
Forum: rodboard 3 years ago
Tony Papazian
11. Guide Setup 2
<p>Do I need to add one more guide?</p>
Forum: rodboard 3 years ago
Tony Papazian
12. Guide Setup
<p>Do I need to add one more guide?</p>
Forum: rodboard 2 years ago
Tony Papazian
I just wanted to thank Don & Ken at American Tackle for finding the part I was looking for & Joe at HFF Custom Rods for tacking care of my needs with great customer service. Joe has earned a new customer.
Forum: rodboard 2 years ago
Tony Papazian
Spencer Phipps Wrote:
-------------------------------------------------------
> Did you try Angler's Workshop?
Sure did.
Forum: rodboard 2 years ago
Tony Papazian
Hello Everyone,
I have searched everywhere for some American Tackle size 16 EVA Fore Grip for G2 Uni-Lock Hood. If anyone knows of anyone that might have a couple that I could purchase I would be very appreciative. Thanks
Forum: rodboard 2 years ago
Tony Papazian
Is there a formula for reel seat placement? I'm building a spinning rod & I've just gone by how my factory rods are setup. Any advise would be appreciated.
Forum: rodboard 3 years ago
Tony Papazian
Roger,
Thanks for the response. After reading everyones responses it looks like your method & the two line static load test will accomplish the same objective. I will give both a try but I'm assuming the two line static test will be easier & quicker to accomplish the task at hand as I can just slide the guides on with tubing or rubber bands then adjust them with the line going through
Forum: rodboard 3 years ago
Tony Papazian
Thanks everyone. I need to order some more guides & play around with it to what work best.
Forum: rodboard 3 years ago
Tony Papazian
Norman Miller Wrote:
-------------------------------------------------------
> I checked your other posts. It appears to be 7'2"
> light drop shop blank with a KR 16H based
> reduction train. The KR GPS will probably
> recommend 5 runners, and in my opinion is at least
> one too few, maybe two. On such a rod I will
> normally use 9 to 10 guides total.
That is co
Forum: rodboard 3 years ago
Tony Papazian
Below are links to 4 photo's of the dropshot rod I'm setting up. Do you think I need to add one more guide to running guide?
Forum: rodboard 3 years ago
Tony Papazian
Thanks for the response. I guess I should slow down & read the instructions carefully. Total brain fart on my side as I measured from the tip to the spool axle instead of the butt to the spool axle. Everything is good now. Thanks for responding.
Forum: rodboard 3 years ago
Tony Papazian
I've only built a few rods but this will be my first using the KL-H guides. I've entered all the information into the software & this is what it came up with. Can someone explain how to take this information & convert it into inches so I know where to put the guides? Am I assuming correctly that the stripper guide is to be at 19" in front of the spool axle? If that's correct I'm jus
Forum: rodboard 3 years ago
Tony Papazian
27. Re: Guide Advice
Well I received all my components to start my build. I order the 16H, 8H, 5.5M for the reduction guides & I'm really surprised at how small they are.
Forum: rodboard 3 years ago
Tony Papazian
29. Re: Guide Advice
Jim,
Did you stay with the 5.5 over the 4.5 or 4 to give you more options if you were to up your line size? The largest line size I'll be usuing on this rod is 10lb braid & 8lb flouro.
Forum: rodboard 3 years ago
Tony Papazian
30. Re: Guide Advice
Thanks Jim. The 2500 & 3000 reels are the same size reel with just a different spool capacity. What size running guides do you go with?
Forum: rodboard |