THANKS Everybody, I will try the blue ice trick as I have some in my freezer that I use for camping. Will get back to you all with results "Bent Rods To Ya" Darrel
Forum: rodboard

No I'm using the right stuff, been doing this a long time
Forum: rodboard

All Having trouble with my epoxy setting up quickly. within 5 minutes of mixing, it's like I'm working with saltwater taffy. I'm am only able to apply to one or two guides before I have to either stop or mix a new batch. I live in Nor. Ca. so the weather changes everyday. Wednesday over 100, yesterday, 70s "Bent Rods To Ya" Darrel
Forum: rodboard

Thanks all who responded. I've never heard of pit paste, who sells it?? "Bent Rods to ya all!! Darrel
Forum: rodboard

Anybody know of a product or solution to filling voids in cork rings after they have been installed and sanded?
Forum: rodboard

Thanks to all for responding with advice on epoxy coating, and you others for your opinions. "bent rods to ya" Darrel
Forum: rodboard

Fellow builders, I'm using 100% metallic thread on my latest build. What is you take on the use of color preserver. Should i use it, or go with just epoxy?
Forum: rodboard

Need some advice on installing a foam grip that has a smaller ID then OD of rod butt. I tried to ream it out, but was not very successful. Also what is difference between EVA, Hypalon and just plain foam ??? "Bent Rods to ya" Darrel
Forum: rodboard

Thanks, Everybody who responded!! "Bent Rods to ya" Darrel
Forum: rodboard

Hay Gang, Need some help on best way to trim off about 1 inch from the butt of latest build.. I miss measured the size of the butt cap and need to shorten it by about an inch. I have considered using a grinder with very thin grinding wheel. Or a hacksaw, Any help/advise would be welcomed " BENT RODS TO YA" Darrel
Forum: rodboard

Need some advice on using pigment in epoxy. Seem like each time I use some pigment in my epoxy it take a lot longer to cure (dry). Sometimes days to dry and remains sticky. Any advise would be welcomed!! THANKS Darrel
Forum: rodboard

Guys, Problem solved!!! Made contact with Batson and they are sending me a new complete drive set up, BOTH dryer and wrap motors,No wires to mess with!! 3 screws off and 3 back on, that simple. If any of you experience a similar problem contact Batson right away and they will "Hook you up" Thanks again to all who responded. In this forum I always seem to get a solution to any issues I
Forum: rodboard

Roger, I tend to agree with you. I have checked wires and all are intact and power supply is good as nothing has changed in my work shop that would effect power supply, But thanks to those who suggested I check. I will contact Batson on Monday to see if they can help me, other wise I have a huntin buddy who is an electrical guru Thanks again to all who replied!! "Bent rods to ya" Dar
Forum: rodboard

Scott, I had same issue on my last build (Sturgeon Rod) Was told by AW that they no longer carry and were unavailable. I finally bought an American Tackle Company reel seat from Mud Hole. Price is comparable and I think they have a few more choices when it come to combination of colors. I bought 3 of them and last build was very nice. Check it out!! "Bent Rod to ya" Darrel
Forum: rodboard

Fellow builders, I am having problems with my Forecast drying motor. It is in combo with a separate wrapping motor tied to an Alps chuck uggrade. The problem is the drying motor changes (direction) rotation for no reason. I have loosened the mounting screws, which seems to help. I also change the drive belt (O Ring). The multi drive pulley will not tighten securely to the shaft of drive motor. T
Forum: rodboard

Thanks to all who have responded to this post, and yes Nuno I did get your e mail Thanks again. I am on my way to getting started!! "Bent rods to ya" Darrel Vacaville, Ca.
Forum: rodboard

Fellow builders, Having just seen article in latest issue of Rodbuilder about marbling. Was hoping some of you have some history with this practice. I have a couple questions on this 1 What type of pigment is best. What type of based is used, Epoxy, Acrylic,Oil, water??? and best place to buy, IE paint store, Car paint shop???? 2 Do you thin it with anything and if so what? 3 I understand a b
Forum: rodboard

Guys, Anybody have any comments on the use of a tool rest (Alps) for turning handles, mandrels etc.?? Thinking about buying one ($80) from AW Thanks "Bent Rods to ya" Darrel from CA.
Forum: rodboard

Guys, Need some advice on how to center my cork pieces when reaming them out. I use a drill with the Alps reamers and do it by hand with each piece. However some of them are not centered, making my job of shaping handle more difficult. ANY advice would be helpful!! Thanks "Bent Rods to ya" Darrel from CA.
Forum: rodboard

David, Just finished a build using fingernail art decals (sports teams) I recommend a full day of drying before any epoxy is applied. The build was Awesome. Very well received!! "Bent rods to ya" Darrel
Forum: rodboard

Paul, I have done a few cord wraps recently, My opinion is this, I use flexcoat thread sealer generously on the cord. This helps bond the cord to rod in addition to the type glue you use. (I use two ton epoxy) Then to finish I use a Clear wood lacquer from a spray can bought at my local Ace Hardware. I agree with Nick as I to, think that the Atwood cord is much better, It is stiffer and has 2 mor
Forum: rodboard

All, Can anyone help me with a couple questions on building an acid wrap rod 1. Spline, up or down from reel seat 2. what degrees or how many guides to make the 180 degree change? Like every 30,45,60,90 degrees? what do you think is best. 3. Ideal length. I will use mainly on boat Thanks everyone "Bent rods to ya" Darrel
Forum: rodboard

Anybody remember the name of sponsor that sold a product called SYNCORK I can't remember their name Bent rod to ya
Forum: rodboard

Fellow builders, I met with a saddle maker and my handicapped friend yesterday and we have an exciting prototype grip to help the "one armed fisherman" This could open the door for many of our handicapped fishing friends.. MORE TO COME!! "Bent rods to ya" Darrel
Forum: rodboard

Thanks everybody, I will try these ideas and get back to you all!! "Bent rods to ya"
Forum: rodboard

Anybody have some tips on final cut. I have issues with frayed string when final cut is made. I use a new blade for each build.. I use silk thread???? Suggestions??? bend rods to ya darrel
Forum: rodboard

All, Started working with saddle smith who has some GREAT ideas on how to make this work for someone with a hook. Will keep you all in the loop!! WE can open new door for these fishers. Let's work together on this one!!! Bent rods to ya darrel
Forum: rodboard

Matt, Do you have any pic that might give me an idea of what you mean?? I don't get the velcro wraps Bent rod to ya darrel
Forum: rodboard

Thanks everybody, some GREAT ideas here. The aluminum fore grip sounds good, however I think the metal to metal might not have a holding power needed, But You have given me an idea to use leather as a front grip and have it installed at a saddle shop near by. I will go there today. Just so you know he wants to fish steelies in Northern CA, from the bank. The spinning rod I'm building is a 7.2&quo
Forum: rodboard

All, Anybody ever build a rod for a person with a prosthetic arm/hand (hook). My good friend loves to fish and wants to take up bank fishing (only fished from a boat in the past) I need to figure out a way of keeping the rod from twisting as he turns the crank. His hook can really tear up a fore grip in just one trip. We use a rail plate (OLD SCHOOL I KNOW<BUT IT WORKS) when boat fishing to ke
Forum: rodboard