SPONSORS
2025 ICRBE |
Adding a ferrule to a graphite fly rod
Posted by:
Michael Schweit
(---.cable.mindspring.com)
Date: May 21, 2019 09:52PM
I have a Sage 2 piece RPLXi and would like to make it a 4 piece. Can this be done? Re: Adding a ferrule to a graphite fly rod
Posted by:
Tom Kirkman
(Moderator)
Date: May 21, 2019 10:53PM
Yes, with some glass sleeving to use as an oversleeve ferrule. We've done some articles in RodMaker about this. It can be done and done well.
However, unless you want to go to a lot of time, trouble and relatively critical work, I'd just buy a 4-piece blank out of the box and build a new rod. ................ Re: Adding a ferrule to a graphite fly rod
Posted by:
Michael Schweit
(---.cable.mindspring.com)
Date: May 21, 2019 11:28PM
Thanks Tom. As I have the blank already, can you direct me to those articles? I realize it takes additional time but I love doing these things. M Re: Adding a ferrule to a graphite fly rod
Posted by:
Tom Kirkman
(Moderator)
Date: May 22, 2019 07:18AM
I would have to go look through the back issues. Will try to get to it sometime today or tomorrow.
Keep in mind any warranty on your blank will go out the window with this alteration. On the other hand, if you enjoy this type of work, you'll certainly enjoy this project. ................ Re: Adding a ferrule to a graphite fly rod
Posted by:
Robert A. Guist
(---.triad.rr.com)
Date: May 22, 2019 10:18AM
Hello Michael & Tom.
I found at least 18-20 articles on "Ferrules" in RodMaker Magazine. There are 2 I off the top of my head 1 from Ralph O'Quinn in Volume 4- Issue 4, and 1 from Tom Kirkman in Volume 16- Issue 2. Hope this helps, I lost most of my magazines to Florence. Tight Wraps & Tighter Lines. Bob, New Bern, NC. Edited 1 time(s). Last edit at 05/22/2019 07:03PM by Robert A. Guist. Re: Adding a ferrule to a graphite fly rod
Posted by:
Michael Danek
(---.alma.mi.frontiernet.net)
Date: May 22, 2019 11:40AM
I think you should keep in mind that this may turn a great rod into almost scrap. It is not without risk. Re: Adding a ferrule to a graphite fly rod
Posted by:
Michael Schweit
(---.cable.mindspring.com)
Date: May 22, 2019 03:54PM
I get the risks and appreciate the warnings and concerns. Robert and/or Tom, is there a way for me to purchase back issues on-line about the ferrule articles? Re: Adding a ferrule to a graphite fly rod
Posted by:
Tom Kirkman
(Moderator)
Date: May 22, 2019 04:49PM
Not online. I will have the find the issue with the article on making ferrules. It's probably been a few years back, now.
................. Re: Adding a ferrule to a graphite fly rod
Posted by:
herb canter
(---.atmc.net)
Date: May 22, 2019 08:35PM
Hopefully it's one of Sages " less expensive " blanks if those even exist. Re: Adding a ferrule to a graphite fly rod
Posted by:
Bill Sidney
(---.gci.net)
Date: May 22, 2019 10:33PM
get a cheep BLANK to work on first an see how it comes out before you do it to a GOOd SAGE, I think, most of the jobbers on the left have cheep blanke to work on William Sidney AK Re: Adding a ferrule to a graphite fly rod
Posted by:
Phil Erickson
(---.dsl.pltn13.sbcglobal.net)
Date: May 22, 2019 10:41PM
Michael, the RPLXi is one very nice blank! I have an 8wt 9' 3 pc that is my go-to Bonefish rod. If I was you, I would seriously think about making it a 3pc, thus eliminating one homemade ferrule. Re: Adding a ferrule to a graphite fly rod
Posted by:
Michael Schweit
(---.cable.mindspring.com)
Date: May 22, 2019 11:05PM
Phil, I have Xis from 6 to 12 and love them all. I am not welcome in most fly shops as I feel I have never cast these rods to their potential so I have to keep them ;-) As for your math, let me know how to turn a 2 piece blank into a 3 piece. Must be new math. Re: Adding a ferrule to a graphite fly rod
Posted by:
Michael Schweit
(---.cable.mindspring.com)
Date: May 23, 2019 12:13AM
Robert, I missed your post. I will check into back issues. Michael Re: Adding a ferrule to a graphite fly rod
Posted by:
Phil Ewanicki
(---.res.spectrum.com)
Date: May 27, 2019 09:04AM
Mike: Cut the tip section in half. Voila! Three-piece rod. Re: Adding a ferrule to a graphite fly rod
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: June 05, 2019 11:17AM
Micheal, here is a post by Mark Talmo concerning ferrule fabrication. He loaned me a rod which he outfitted with his ‘CARL’ ferrule. I was quite impressed with its performance. [www.rodbuilding.org]
Norm Sorry, only registered users may post in this forum.
|