SPONSORS
2024 ICRBE EXPO |
CRB RBS Base thread carriage
Posted by:
Seth Johnson
(---.hsd1.tx.comcast.net)
Date: January 31, 2018 10:01PM
Is there another option for a thread carriage besides the CRB HWS-1? I need more than 2 spools at a time, and in general I’m not in love with the HWS-1. Wondering if this PAC Bay 4 Spool or this Batson would work? Open to any suggestions.
[www.mudhole.com] [www.getbitoutdoors.com] Re: CRB RBS Base thread carriage
Posted by:
Jay Dubay
(---.try.wideopenwest.com)
Date: February 01, 2018 03:14AM
I believe it will, I have this one on a CRB track, It's just a different version glides like it's on ICE ! [www.mudhole.com] And the top piece [www.mudhole.com]. Cheers Jaa Re: CRB RBS Base thread carriage
Posted by:
Seth Johnson
(---.williams.com)
Date: February 01, 2018 08:22AM
You wouldn’t happen to have a picture of your setup would you? Re: CRB RBS Base thread carriage
Posted by:
Robert Wood
(162.252.129.---)
Date: February 01, 2018 09:54AM
I made an extension for my CRB carriage I can run up to 6 spools on it. Its easy to do too a couple pieces of aluminum strap 3/4 inch wide and a few nuts and 1/4 all thread Re: CRB RBS Base thread carriage
Posted by:
Seth Johnson
(---.williams.com)
Date: February 01, 2018 12:40PM
Robert Wood Wrote:
------------------------------------------------------- > I made an extension for my CRB carriage I can run > up to 6 spools on it. Its easy to do too a couple > pieces of aluminum strap 3/4 inch wide and a few > nuts and 1/4 all thread I am kicking myself right now. I had pretty much melted my first HWS-1 trying to replace the tension rod and recently ordered a new one. Instead of stripping the hardware, I tossed the whole thing. This sounds like a good idea, and I think I may go with it. If I were just starting out, Jay's idea looks better, but I don't want to drop more money than I have to into this. The two things I'm not seeing at Home Depot are the springs and plastic washers, but I can order those tonight after I measure the existing ones. What I'm trying to do is get setup to do a tiger wrap with 3 colors. I think I was looking for the 4 spool tensioners I posted to hold tension on 4 spools at the same time, but after reading the instructions it would appear that's not what they do. They hold 4, but only recommend using the tension on 1 spool at a time. Re: CRB RBS Base thread carriage
Posted by:
Robert Wood
(162.252.129.---)
Date: February 01, 2018 01:27PM
I don't know if you have a menards around you but I know they carry the springs and plastic washers Re: CRB RBS Base thread carriage
Posted by:
Robert Mckee
(---.126.140.67.dynamic.ip.windstream.net)
Date: March 11, 2018 05:20PM
If Ace hardware doesn’t have it no one does. Re: CRB RBS Base thread carriage
Posted by:
Robert Mckee
(---.73.185.173.ip.windstream.net)
Date: March 17, 2018 07:58PM
I would love to see it when you get it finished. I have a very limited area I can work in. If you do not mind sharing. Thabks Re: CRB RBS Base thread carriage
Posted by:
Seth Johnson
(---.williams.com)
Date: March 19, 2018 07:18AM
The photo uploaded sideways, but here it is.
[www.rodbuilding.org] Sorry, only registered users may post in this forum.
|