SPONSORS
2024 ICRBE EXPO |
High sticked a rod, repairable?
Posted by:
Adam Lancia
(---.hsd1.al.comcast.net)
Date: December 22, 2016 09:49AM
Hi all, I was fishing last week and hooked into a fish fairly close to where I was standing. I set the hook and must have either been a little overzealous or I didn't have the drag backed off enough. Either way, the rod snapped 21" from the tip on a 6'7" rod. It's a medium fast rated 3/16 - 1/2 oz. The I.D. is .158" and the O.D. is .203". What is the best way to repair this? If nothing else, this will give me some practice. I realize the action will change but I'm not really hung up on that as long as I can potentially use the rod again.
Thanks in advance! Re: High sticked a rod, repairable?
Posted by:
Tom Kirkman
(Moderator)
Date: December 22, 2016 10:35AM Re: High sticked a rod, repairable?
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 22, 2016 11:05AM
As Tom's link says, a fiberglass repair blank on the inside and outside of the blank with a short thread wrap at each end of the repair will repair the rod nicely.
One issue you will have is with the location of the break. With the break at 21 inches from the tip of a 6'7" blank, you will certainly stiffen the rod some at this location. Normally in a typical rod, this is the location of the blank where the rods action tends to change and normally there is a lot of flex at the location. As a result of the splice, you will stiffen the rod to some extent - depending on your splice but it will still work for fishing. Be safe Re: High sticked a rod, repairable?
Posted by:
Adam Lancia
(---.hsd1.al.comcast.net)
Date: December 22, 2016 11:14AM
Thank you Tom, that's exactly what I was looking for!
Roger: will that mean a faster blank, or slower? Does anyone know where I can source the appropriate pieces to splice this rod? Thank you both! Edited 1 time(s). Last edit at 12/22/2016 11:22AM by Adam Lancia. Re: High sticked a rod, repairable?
Posted by:
Chuck Mills
(---.grenergy.com)
Date: December 22, 2016 11:38AM
One source of fiberglass blank material is a cheap telescoping crappie rod from Walmart. I think I bought a 10 footer for my last repair. Definitely read and follow the article by Ralph O'Quinn. It works. The rod won't be exactly as before, but it will be fishable.
This repair may make the blank slightly stiffer (faster). _________________________________________ "Angling is extremely time consuming. That's sort of the whole point." - Thomas McGuane Edited 1 time(s). Last edit at 12/22/2016 11:39AM by Chuck Mills. Re: High sticked a rod, repairable?
Posted by:
Tom Kirkman
(Moderator)
Date: December 22, 2016 12:11PM
The action won't really change, but the speed of the rod will. The addition of the extra weight will cause the reaction and recovery time to slow a bit. As far as stiffening the blank, using glass instead of graphite will help, but you will likely stiffen the rod at that point a bit. Of course, the alternative is to junk the rod so I'd go ahead and do what you can if you want to salvage it in some form or fashion.
........... Re: High sticked a rod, repairable?
Posted by:
Spencer Phipps
(172.56.39.---)
Date: December 22, 2016 01:06PM
I find a lot of glass rods at garage sales going for $3 to $5 including an old reel, I just throw them in a long cardboard box I have setting vertical in the garage. Gives me old school spare guides and repair materials. Re: High sticked a rod, repairable?
Posted by:
Rolly Beenen
(---.ontariopowergeneration.com)
Date: December 22, 2016 01:59PM
unless you are coming home I can fix it for you. Rolly Beenen Rovic Custom Rods Re: High sticked a rod, repairable?
Posted by:
Adam Lancia
(---.hsd1.al.comcast.net)
Date: December 23, 2016 10:15AM
Thanks for all the ideas gentlemen, I really appreciate it!
Rolly: I won't be home anytime soon. Hope things are well up there! Re: High sticked a rod, repairable?
Posted by:
Adam Lancia
(---.hsd1.al.comcast.net)
Date: May 04, 2017 07:31PM
After not having this rod in the rotation for 5 months, it's about time I tried my hand at fixing it. I'm not having any luck finding the correct size pieces of blank to use for the repair though. There's one more place I'm going to check that might pan out, bt barring that, do any of you fine gentlemen feel like digging through your stash of broken bits and pieces to see if you have something that I could use...? Fiberglass or graphite is fine as I'm not too worried about the performance characteristics as much as I am about the actual size of the pieces. I have plenty of good Karma to offer in return, plus the shipping costs.
Thanks in advance! Sorry, only registered users may post in this forum.
|