SPONSORS
2024 ICRBE EXPO |
Guide foot glue stick
Posted by:
Thomas C Kuzia
(32.216.23.---)
Date: July 15, 2016 09:42AM
I'm having a terrible time trying to hold the smaller guides to the rod prior to wrapping them and am wondering if the glue sticks from a common glue gun would work as well as the guide foot glue sticks?
Would either types have any affect on the epoxy holding? I've tried 1/4" and 1/8' masking tape to hold the guides but both are too wide and the 1/8" doesn't give much holding surface. Thanks,,, Tom Re: Guide foot glue stick
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: July 15, 2016 09:59AM
Tom the common glue sticks should work as long as it is a LOW temp glue. The issue and why I only use the flex coat is the ability to move the guide once it is wrapped to get a perfect alignment of your guides. I would suggest that your try it on a spare blank or it the grip area where you can remove it a cover with the grip. If it holds and can be moved you are good to go.
The glue has no effect on the epoxy, be sure you clean up any that squeezes out from under the guide foot. It doesn't take much to hold the guide. Tom Re: Guide foot glue stick
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: July 15, 2016 10:05AM
Thomas,
Use Orthodontic ligature ties to hold the guides on the blanks. [www.amazon.com] Just slip enough ties onto the blank before you start positioning the guides. After the guide is wrapped, use a nipper cutter with a sharp tip to cut the tie to finish the wrap. Also, make sure that the guide has been prepped, so that the thread easily climbs up the foot without any hassle. Re: Guide foot glue stick
Posted by:
Thomas C Kuzia
(32.216.23.---)
Date: July 15, 2016 10:55AM
Thanks Roger and Tom!
I'll try both suggestions! Tom Re: Guide foot glue stick
Posted by:
Bill Sidney
(---.gci.net)
Date: July 15, 2016 11:48AM
the glue never worked for me could not move them once it was wrapped , I use thin rubber bands , stretch, rap a few turns an tie , cut off
after you start the wrap , I tried rubber sewing thread but lots of fuzz don't like , about 3 wrap's of stretch thin rubber bands will do it for me , got the bands from local big box store, every one has there way of doing it . what ever works for you , William Sidney AK Re: Guide foot glue stick
Posted by:
Donald R Campbell
(---.socal.res.rr.com)
Date: July 15, 2016 12:46PM
Tom,
I use elastic thread to temporarily tie on micro guides. That way, when static loading the blank, I can adjust the guide positions as necessary. I then leave the elastic thread on the guides and wrap up to the elastic thread, after securing the guide foot with the final wrap, and then cut off the elastic thread with a razor blade. On the real small footed tip guides, I use the guide foot glue; but I make sure not to apply too much glue to the bottom of the guide foot. Just enough to make the bottom of the foot shiny. Don Campbell don@sensorfishingrods.com Re: Guide foot glue stick
Posted by:
curtis drumm
(---.hsd1.md.comcast.net)
Date: July 15, 2016 08:44PM
I cut pieces of surgical tubing of various diamaters. Re: Guide foot glue stick
Posted by:
Ken Preston
(---.opera-mini.net)
Date: July 16, 2016 07:26AM
I used to cut up slices of surgical tubing (and still have some left around) but, like Roger I changed over to orthodontic ligature bands. They come in many sizes, eliminate the time cutting the surgical tubing and are all the same width (in each dimension). Big time saver - and can be found on line almost as cheap as a length of good quality tubing. Re: Guide foot glue stick
Posted by:
Thomas C Kuzia
(32.216.23.---)
Date: July 16, 2016 10:59AM
A lot of ideas I never thought of using!
It's amazing to me how many different things can be used in an entirely different way then they were designed for! The key is knowing what's out there! Thanks again,,, Tom Re: Guide foot glue stick
Posted by:
Mat Peirce
(72.50.244.---)
Date: July 18, 2016 06:29PM
I use gel super glue Re: Guide foot glue stick
Posted by:
Thomas C Kuzia
(32.216.23.---)
Date: July 20, 2016 09:36AM
I tried the regular hot glue on an old guide yesterday and it worked pretty good.
I heated the guide with a lighter and touched the glue stick to the guide and set it on an old rod blank.Let it sit a minute and it was held on pretty good. I put a little too much glue on but I can remedy that next time. Thanks again,,, Tom Kuzia Re: Guide foot glue stick
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: July 20, 2016 09:49AM
Thomas,
Yes, one can use some sort of glue on a guide foot to hold the guide in place while wrapping. But, now you have to deal with the glue that is on the guide foot, when it comes time to alignment etc. Also, if you have a bit too much glue on the guide foot, you have issues with that. Plenty of ways to hold a guide foot nicely to the blank without having to deal with the after math of using any sort of glue to hold the foot to the blank. But, certainly if you wish, and if you are happy with the results, use any method that you wish to hold the foot in place while wrapping. Be safe Re: Guide foot glue stick
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: July 20, 2016 10:16AM
Roger
I like your dental ligature bands and use them as they are easy to work with too. The smallest i have found are 1/8 inch and when applying guides at the tip of bass rods that have a 4.5 to 5 tip they aren't small enough to hold the guide. It is in that area that I use the guide stick glue. if you have any ideas on how you handle those small tips I sure would like to know. If you have found any bands that are 1/16 they would work but I haven't seen any online. Also if you use the Flex Coat guide foot glue and once the guides are wrapped it is very easy to move the foot for alignment. The glue has no strength. Tom Re: Guide foot glue stick
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: July 20, 2016 11:47AM
Ron
Thanks for the email on where to find the smaller bands. Going to order some today. Tom Sorry, only registered users may post in this forum.
|