SPONSORS
2024 ICRBE EXPO |
restoring a Scott G series that is really beat up
Posted by:
Jesse Shipe
(---.29.226.218.res-cmts.sha.ptd.net)
Date: June 06, 2016 09:27PM
Hello all,
Its been awhile since I have done some rod work, but Im about to get back into an old project. I have a Scott 8 1/2' 5 wt. G series rod that is really hammered. The problem that I am having is removing the left over epoxy on the guides that were on the blank. It is very difficult to remove and is chipping the original finish off of the rod. I would like to retain the original "taped" look if possible, but I am wondering if it would just make more sense to totally refinish it with a sanded and dull matt type finish. I have done this before, but I prefer to keep the rod looking something like it did when new. Suggestions?? Thanks. Jesse I have tried the credit card and heat... not much happening with that. Re: restoring a Scott G series that is really beat up
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: June 07, 2016 05:32PM
A little I mean little heat will soften the finish then a razor blade over the foot to cut the thread Peal it off Re heat and grab a threat and undo the rest of the thread When warm - Not Hot -- it comes off pretty clean
But I would suggest strip the finish all off and refinish You will probably have to re-locate the guides any way Bill - willierods.com Re: restoring a Scott G series that is really beat up
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: June 07, 2016 06:14PM
Be careful with heat. I learned the hard way once when I was using a heat gun to soften some epoxy and the section I was beating folded over. This happened on the low heat setting. I now use a hair dryer it is much easier on the blank then a beast gun. If you are going to put the guides back in the same place clean up the best you can without removing the original rod finish rewrap and epoxy; will not know you rewrapped.
Norm Re: restoring a Scott G series that is really beat up
Posted by:
Phil Erickson
(---.dsl.pltn13.sbcglobal.net)
Date: June 07, 2016 06:20PM
It may not be epoxy, if not heat is no help. Re: restoring a Scott G series that is really beat up
Posted by:
eric zamora
(---.lightspeed.frsnca.sbcglobal.net)
Date: June 07, 2016 07:21PM
Contact Scott Fly Rods, ask the what they would suggest.
eric fresno, ca. Re: restoring a Scott G series that is really beat up
Posted by:
Jesse Shipe
(---.29.226.218.res-cmts.sha.ptd.net)
Date: June 07, 2016 09:50PM
eric zamora Wrote:
------------------------------------------------------- > Contact Scott Fly Rods, ask the what they would > suggest. > > eric > fresno, ca. That is a good idea. What ever they put on the line guides, its tough stuff. Thank you. Re: restoring a Scott G series that is really beat up
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: June 08, 2016 08:42AM
I just got a new heat gun I first thing I thought about was it is hotter then a hair dryer But if careful you can do it Just move faster and a lot farther away from what your heating Bill - willierods.com Re: restoring a Scott G series that is really beat up
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: June 08, 2016 08:47PM
Bill,
On your new heat gun, do you have an adjustable air supply? If so, you will find that when you leave the air supply wide open, the heat is much cooler than if the air supply is fully shut off. Be safe Re: restoring a Scott G series that is really beat up
Posted by:
Jesse Shipe
(---.29.226.218.res-cmts.sha.ptd.net)
Date: June 09, 2016 06:16AM
The folks at Scott got right back to me. They suggested a wiping rag with toulene or acetone.
I have found that I can scrape the epoxy with a PENNEY. It is softer than steel, harder than plastic, and its not gouging my blank.... This is a slow process, no matter how you do it. Re: restoring a Scott G series that is really beat up
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: June 09, 2016 05:37PM
Roger
Same force of air yet two heat settings I played with it before I put it on a rod Even on low heat it is HOT I may self have replaced a blank even from a hair dryer - ( don't watch TV while heating finish ) Ya got to be Careful But it is a lot quicker to use I have to find a better way to blow any dust off a rod - Maybe get another hair dryer - ??? With high air force On cold Bill - willierods.com Re: restoring a Scott G series that is really beat up
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: June 10, 2016 11:43AM
Bill,
Open all of the windows in your rod building area. Plug in your electric leaf blower and go over every square inch of your rod building area, including ceilings, walls, floors and benches. Here is a nice inexpensive blower that works very well to blow everything that is not nailed down out the window of your rod building area. [www.homedepot.com] Obviously you will have put away any thing that can be blown away. Do this two or three times over the course of a couple of days and you will not have a spec of dust anywhere in your shop. === By the way, I am not kidding. I do this all of the time in the outbuilding where I do all of my "dirty" word. i.e. sanding, turning etc. I open up the windows and use my air compressor and blow gun to blow everything out the doors and windows to insure that the area is free of dust. I always do it before starting work to be sure that there is nothing on the floors, walls or shelves that might otherwise contaminate a good job. Be safe Be safe Re: restoring a Scott G series that is really beat up
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: June 10, 2016 12:37PM
I can see the mess that blower would make with all the stuff on the floor My sisters nick nakes on the tables ( living room ) I spray water on most every thing before finishing a rod That seems to do a good job to keep it down LOL
I envy the guys that have one room as The Shop Bill - willierods.com Edited 1 time(s). Last edit at 06/10/2016 12:39PM by bill boettcher. Sorry, only registered users may post in this forum.
|