SPONSORS
2024 ICRBE EXPO |
K-Sun printer decals cloudy
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: June 08, 2014 09:59PM
Just received my K-Sun 270 decal printer and need a little advice. The first decals I made were gold on clear. The print turned out beautiful, but after I put it on the rod and epoxied it, you can see the tape is cloudy. The factory decal from AT also in gold on the Matrix blank is clear as glass.
Has anyone else experienced this? I was wondering if I needed to do anything special on the application? Thanks for any input. Tom Re: K-Sun printer decals cloudy
Posted by:
Rod Churchward
(---.lns20.bne1.internode.on.net)
Date: June 09, 2014 06:02AM
Hi Tom,
That could be the glue on the backing showing through. I have found that a thin coat of finish on the blank, can help. Kind regards, Rod, Mboro Qld. Australia. Re: K-Sun printer decals cloudy
Posted by:
Rod Churchward
(---.lns20.bne1.internode.on.net)
Date: June 09, 2014 06:19AM
Tom,
Either that, or go to a solid colour, like gold on black tape for example, there are heaps of colour schemes. You can stick your fingers all over the glue underside and no one will ever know. Regards, Rod. Re: K-Sun printer decals cloudy
Posted by:
Pat Barnard
(12.227.181.---)
Date: June 09, 2014 07:24AM
Have not had that issue. Only issue is trying to eliminate the decal edges from showing.
Pat Barnard Re: K-Sun printer decals cloudy
Posted by:
Tom Kirkman
(Moderator)
Date: June 09, 2014 07:51AM
It's important to really get the decal stuck down tight to the blank. A brayer/roller can help do this. Any time you have insufficient contact, even a very minute difference, it can show up as a slightly cloudy area, even across the whole decal.
................. Re: K-Sun printer decals cloudy
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: June 09, 2014 08:55AM
I have used 7 or 8 of the decals in both gold and silver on both matt and gloss finish blanks applied directly to the blank and have not had any issues at all. I do use a brayer after application also. Ron Weber Re: K-Sun printer decals cloudy
Posted by:
Lance Dupre
(---.lightspeed.nworla.sbcglobal.net)
Date: June 09, 2014 09:26AM
Get yourself a roller, it works wonders. Re: K-Sun printer decals cloudy
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: June 09, 2014 03:16PM
Looks like I am going to get a roller and give it a go. Thanks to all for your suggestions
Tom Re: K-Sun printer decals cloudy
Posted by:
Rod Churchward
(---.lns20.bne1.internode.on.net)
Date: June 09, 2014 10:07PM
Hi Tom,
I'm with you, I'm off to get one as well. Regards, Rod. Mboro Qld. Australia. Re: K-Sun printer decals cloudy
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: June 09, 2014 10:16PM
Got it tonight and will be putting a decal on tomorrow. We'll let you know how it looks.
Tom Bel Air Maryland Re: K-Sun printer decals cloudy
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: July 01, 2014 03:17PM
A bit slow on the response but I wanted to thank those for the replys and suggestions. I bought the brayer and rolled the decals down on my next few builds and they turned out perfectly.
Thanks Tom Sorry, only registered users may post in this forum.
|