SPONSORS
2024 ICRBE EXPO |
PacBay RW-XL replacement rod support
Posted by:
Jon Meyers
(---.mpls.qwest.net)
Date: March 29, 2014 10:02AM
Hey everyone,
Do taking a reel seat off last night and things got a little rough...one thing lad to the next and before I knew it my middle rod support had busted off where it adapts to the rod smith rails. The problem is I can't find any replacement rod supports for this wrapper online. Was hoping someone may know where to look? Thanks for the help, Jon Re: PacBay RW-XL replacement rod support
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: March 29, 2014 10:35AM
Jon,
This appears to be a Pac Bay product. [www.fishpacbay.com] I would think that you could contact any pac bay distributor and ask them to order the part - which is the rod support and found on page 3 of your manual. Be safe Re: PacBay RW-XL replacement rod support
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: March 29, 2014 10:38AM
For example - check with Anglers Workshop:
[www.anglersworkshop.com] If you look at their page, there is a picture of their single rod dryer, that uses one of the rod supports. So, it would quite likely that they would have a rod support in stock. Either available singly, or as part of the dryer package. Be safe Re: PacBay RW-XL replacement rod support
Posted by:
Garry Thornton
(---.natsow.res.rr.com)
Date: March 29, 2014 11:43AM
I believe that the XL was the model that has three tubes instead of the flat rail used on most wrappers.
I also believe it was discontinued...I would contact Utmost Enterprises, they seem to have a close tie with Pac-Bay. Otherwise someone who sponsors here might have some spare parts in stock. Good Luck. Re: PacBay RW-XL replacement rod support
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: March 29, 2014 01:38PM
Gary,
I stand corrected. [www.fishpacbay.com] However, since the part is still listed in the parts manual, it is possible that a pac bay distributor may be able to obtain it. Be safe Re: PacBay RW-XL replacement rod support
Posted by:
Ken Meissner
(---.abdlwi.dsl.dynamic.tds.net)
Date: April 01, 2014 07:10PM
I have the same problem. Just bought a RW 3L and UPS dropped it from airmail must have been 10,000 ft a lot of broken small parts. I call Pac. Bay and they sent to a dist. to get the parts. The Dist is Donartrods.com . I bought the rod wrapper from Cabelas and they told me to bad call ups. Called UPS they said I should have refused package no one home they just left it on front porch. So I am out looking for parts also to fix at my cost. I will let you know how it goes with the help I get. Re: PacBay RW-XL replacement rod support
Posted by:
Ken Meissner
(---.abdlwi.dsl.dynamic.tds.net)
Date: April 02, 2014 10:03AM
Jon
What part do you need I have to buy a new support complete I will have parts let over from mine. Cabelas nor UPS will help so I have $80.00 more in my wrappen and paid to much for it. Re: PacBay RW-XL replacement rod support
Posted by:
Ken Meissner
(---.abdlwi.dsl.dynamic.tds.net)
Date: April 04, 2014 02:31PM
Got the parts from Donart. The price was fair from them they worked with me and sent extra stuff. Thanks Sorry, only registered users may post in this forum.
|