SPONSORS
2024 ICRBE EXPO |
Wet Saw for Blank Trimming - Recomendations
Posted by:
Marc Morrone
(---.dsl.airstreamcomm.net)
Date: June 23, 2013 06:38AM
Can anyone recomend a particular wet saw for trimming the butt end of blanks? More concerned with ease of use and quality than price.
Thanks! Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: June 23, 2013 10:17AM
You can use any diamond wet saw - used dry to easily trim and chop blanks.
But, perhaps an even better option is the use of a mini chop saw - remove the blade and replace it with a 3 inch abrasive cut off wheel. Or, you could do, as I have done for many years - use an 8 inch conventional miter saw. Replace the blade with a good quality 8 inch abrasive cut off wheel. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: June 23, 2013 10:24AM
[www.harborfreight.com]
and [www.harborfreight.com] or [www.harborfreight.com] or [www.menards.com] and [www.menards.com] Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
Sandy Harris
(---.ec.res.rr.com)
Date: June 23, 2013 11:20AM
I've had good results using a Dremel tool with a cutting disc. I'll mark the blank and rotate the rod keeping the cutting edge lined up with the mark. Just don't rush it. So far I've gotten nice smooth cuts. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
John E Powell
(---.buffalo.res.rr.com)
Date: June 23, 2013 12:28PM
Are you looking for a wetsaw because you want to keep cutting temperatures as low as possible? Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
Marc Morrone
(---.dsl.airstreamcomm.net)
Date: June 23, 2013 12:44PM
Looking at a wet saw to eliminate dust in the shop. Even running my dust collector behind my high speed chop saw does not catch it all. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
Randolph Ruwe
(---.hsd1.wa.comcast.net)
Date: June 23, 2013 01:31PM
Use a jewlers saw and do it by hand. Minimal dust. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: June 23, 2013 09:14PM
Do your cutting, sanding, grinding etc. if a different area that the area where you do your wrapping and coating and it is a none issue.
Never a good idea to do "dirty" work in the same room as for guide wrapping and coating. Difficult if not impossible to keep active dust out of clean wraps and coatings that are drying. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
John E Powell
(---.buffalo.res.rr.com)
Date: June 24, 2013 05:55PM
Marc,
Even a wet saw for cutting tiles will be dirty, unacceptably dirty in my opinion. I'd recommend, as others have,to move your existing saw to a separate "dirty" area outside of your "clean" wrapping/finishing area. Re: Wet Saw for Blank Trimming - Recomendations
Posted by:
John Repaci
(---.ri.ri.cox.net)
Date: June 25, 2013 07:25AM
Marc,
I use a small portable chop saw with an abrasive cutoff wheel; it's small enough to take outside and cut in the driveway. "It ain't what you don't know that gets you into trouble.It's what you know for sure that just ain't so." Mark Twain John in Wethersfield, CT Sorry, only registered users may post in this forum.
|