SPONSORS
2024 ICRBE EXPO |
Rod dryer question
Posted by:
Don Morse
(---.dhcp.aldl.mi.charter.com)
Date: July 11, 2012 04:58PM
Don't want to beat the finish horse to death but here goes.....
I have been using an 18 rpm drier but have recently acquired a 4 rpm set-up. Does anyone use one this slow? What's your opinion of it? I know everyone dries differently but I am just curious what y'all are using for speed. I plan to try it and will form my own opinion, just wonderin'. ______________________________________ Super Tight Lines......Don Re: Rod dryer question
Posted by:
John Martines
(---.hsd1.pa.comcast.net)
Date: July 11, 2012 07:03PM
when doing one rod on a single dryer I stick with the 18rpm but I have a multi drum dryer that uses a 10rpm gear motor that with pulley sizing I have over sped to about 30rpm and a heavy duty speed control switch to slow to the speed I want. The reason is with small diameter rods I can run it faster (about 20rpm) and with larger rods run slower (about 12 rpm) to avoid sling. I think it will depend on what rods you build mostly. Re: Rod dryer question
Posted by:
Chuck Mills
(---.gctel.stellarllc.net)
Date: July 11, 2012 08:12PM
I use 3rpm and 4 rpm microwave motors all the time. _________________________________________ "Angling is extremely time consuming. That's sort of the whole point." - Thomas McGuane Re: Rod dryer question
Posted by:
Col Chaseling
(---.lnse1.ken.bigpond.net.au)
Date: July 12, 2012 01:26AM
Hi Don,
10rpm works good for me. Might be an idea to do a bit of testing before using it on a rod. ESFNEM Col Port Kembla, NSW Australia Re: Rod dryer question
Posted by:
Bruce Johnstone
(96.18.237.---)
Date: July 12, 2012 08:24AM
I use a 7 rpm motor and works fine. All you need is something to keep blank turning so finish doesn't puddle. 3-4 rpm would work very well.
Bruce Re: Rod dryer question
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: July 12, 2012 11:35AM
I have found that for long term drying that speeds of 3-8 rpm are right most of the time.
I have in times passed used speeds up to 25 or so rpm and have found that I get a bit of slinging or gathering of the epoxy in the center of the wrap forming foot balls of finish. After I reduced the drying speed to under 15 rpm, the slinging issues and foot ball formation disappeared. REW Edited 1 time(s). Last edit at 07/13/2012 11:10AM by roger wilson. Re: Rod dryer question
Posted by:
Les Stewart
(---.rh5.cm.dyn.comporium.net)
Date: July 12, 2012 01:48PM
I agree with Roger that under 10 rpms seem to give me the best results. When I use higher speeds I tend to get more "footballs". You only need to turn the blank fast enough to keep your finish from sagging and forming a "belly". Too much speed and cintrifugal force comes into play and will also cause the "belly" effect. Re: Rod dryer question
Posted by:
Tom St.Clair
(---.res.bhn.net)
Date: October 01, 2012 07:39PM
Chuck Mills Wrote:
------------------------------------------------------- > I use 3rpm and 4 rpm microwave motors all the > time. here goes a STUPID question....... I have several microwave turntable motors, most of them are 24 volt........how can I use them with 120v? I would assume that if I "just wired them up and plugged them in" they would burn up very quickly. Would I be corect in that? thanks tom -------------------------------- tom in indy Sorry, only registered users may post in this forum.
|