Anyone know the O.D. cork diameter of this spin handle kit?

DR

Usually they are about 1 +

call mudhole and they will give you the specs on it

[www.mudhole.com]

Bill - willierods.com

Duane the rear OD is approximately .580 and the front that meets up with the reel seat measures .900.
It's very small at the rear end and probably won't be useful on a blank with a rear OD of over .450. They are a good bit smaller than an ECSM seat.

Lance

Thanks Lance!!

DR

Mud Hole would have told him that ???

Bill - willierods.com

Bill, should I have waited for someone from Mudhole to give him the same answer that I just provided for him ? What is it with you anyway ? your most common answers to anyone's questions are either call Mudhole or do a search. If you can't provide the answer just keep quiet. I don't have a problem with Mudhole or any other company for that matter but your answers to everyones questions are pretty much one sided and most of the time doesn't pertain to the question at hand.

Lance

Bill B. mudhole closed at 3pm today. As you can see my post was after that time. I needed an answer today and I searched many sites to no avail. So i came here. Lances answer was greatly appreciated. Thanks everyone.
DR

23mm or 0.9 is spot on for a VSS reel seat however I'd imagine a IPS would taper from 22.2 to 27mm over the cut out ,I guess it might depend on how you measure it as well.
Regards Charlie



Edited 1 time(s). Last edit at 02/18/2012 11:25PM by Charles Clayton.

I appreciate people like Lance who answer a person's question. On the other hand, "call them" , "call me", "I'll send you a PM", or "look it up" does nothing to enrich the value of the forum. I use this forum for reading entertainment and general learning, like hanging around at the store in the old days. Please keep asking questions and giving ANSWERS. Thank-you!!

Well said Jay! And also well said Lance! I also have posted questions and answers far less over the years as people have thrown the look it up or its already been discussed or call blah blah they will tell you the answer. If you don't want to see the question or answer don't look at it or hit back to go to the main list and find something you want to read. In the mean time this forum I believe was set up to share our craft and help beginers to enter the fold. Not to put anyone down or belittle or brush off.

billy broderick Wrote:
-------------------------------------------------------
> Well said Jay! And also well said Lance! I also
> have posted questions and answers far less over
> the years as people have thrown the look it up or
> its already been discussed or call blah blah they
> will tell you the answer. If you don't want to see
> the question or answer don't look at it or hit
> back to go to the main list and find something you
> want to read. In the mean time this forum I
> believe was set up to share our craft and help
> beginers to enter the fold. Not to put anyone down
> or belittle or brush off.


AMEN!!!

Just like thinning finish Everone said it would not work I tried it and it does

Mud Hole has Winter hours -- or who ever you plan to buy from

So i should get upset cause i ask about yellowing on a bam boo blank ?
I got NOW several finishes - I _ have to play with nto find out what works

I guess the world will end - since ya can't make a phone and get your answer -- now

hay lance -- maybe i should have taken your money when you offered it - I don't do things that way !!!

Bill - willierods.com

Mr. Boettcher you seem intent on confirming Mr. Dupre's prognostication! ( ....., and most of the time doesn't pertain to the question at hand.

You continue to let all know "how you do things"..

Bill B. what are you talking about ? Confirms my previous statement.

I think I need one of those icons with a little smiley face guy holding a W T F sign here.

DR



Edited 1 time(s). Last edit at 02/21/2012 10:09AM by Duane Richards.