SPONSORS
2024 ICRBE EXPO |
applying permagloss
Posted by:
John Raymond
(---.90.234.204.Dial1.Detroit1.Level3.net)
Date: January 31, 2003 03:55PM
painted an old blank, want to put permagloss over the paint before i rewrap it, was going to use a coffee filter and wipe it on. the other day i read a post that mentioned cheese cloth. what method works the best? thanks john Re: applying permagloss
Posted by:
Tom Kirkman
(---.WLDF.splitrock.net)
Date: January 31, 2003 04:04PM
I have used cheesecloth with good success. Others tell me that a Kim Wipe or coffee filter is even better. Get it good and wet and make an even and steady pass down the rod. You don't want to have to wipe it more than once or so, as it tacks up quickly and subsequent passes will "hang" and ruin the looks of the finish. Let it dry for a few hours and then come back and apply another "wipe" down. I got by with 3 of these thin coats and usually wound up with a very nice looking blank and a finish that looked and lasted about as good as I could possibly expect. ........... Re: applying permagloss
Posted by:
John Raymond
(---.59.47.224.Dial1.Detroit1.Level3.net)
Date: January 31, 2003 06:19PM
thanks tom, this is one of many things that is so great about this board when a person has a little doubt about doing something they can come here and get an answer. GREAT JOB .. John Re: applying permagloss
Posted by:
Steve Beagley
(---.hevanet.com)
Date: January 31, 2003 08:50PM
This sounds like a good technique, if you were going to coat a multi piece blank how would protect the male end of the ferrules ? Is there a good method that would avoid a masked edge and preserve the original fit of the sections ? I've never tried coating an entire blank, but I have used Permagloss on wraps and I really liked it. I love the pool of experience this board offers, great resource especially for novices like myself. Thanks to all who sponsor and contribute information. Re: applying permagloss
Posted by:
William Colby
(---.proxy.aol.com)
Date: January 31, 2003 08:59PM
I would go ahead and coat the male section and then once everything was dry I would use Scotchbrite to feather that male ferrule area back down until I got back the original overlap of the parts. I wouldn't think you'd get a really heavy thickness with just 2 or 3 such thin coats of the permagloss. Re: applying permagloss
Posted by:
Wylie Wiggins
(---.ca.us.prserv.net)
Date: February 01, 2003 01:45AM
John, You may want to have an extra couple of hands around and do a few blanks at a time with these methods of coating blanks (less wasted materials with the same applicator). Good steady hands are the key to a great finish with these processes. I have seen some work done by a builder that owned A Anglers in Dana Point a few years back (sold now), it produces a terrific finish on the blank. There is also a buffing compound that can be used to bring out an even a higher gloss, it is called diamond something if I am correct. To many beers to be posting now it is time to shut my fingers up? :) Wylie Re: applying permagloss
Posted by:
Bill Boettcher
(---.244.235.197.Dial1.Weehawken1.Level3.net)
Date: February 01, 2003 09:20AM
I myself put on two coats. Let it dry overnight. Wet sand with #400 and water. Then a final coat. Comes out excellant! Nice to wrap on, hard as a rock! And flexable! Re: applying permagloss - additional question
Posted by:
Steve Rushing
(---.us.kpmg.com)
Date: February 03, 2003 10:37AM
I need to re-color a blank and want to use Ralph's method of including the pigment in Permagloss. I would prefer to make up one batch so that I can assure color consistency between coats. Is this possible or do I need to be very meticulous in measuring for multiple fresh batchs. Any suggestions? Re: applying permagloss - additional question
Posted by:
Ed Sabatini
(---.proxy.aol.com)
Date: February 03, 2003 09:05PM
I would think you could do it since you can put on several coats the same day. But you'd need to keep it sealed up and only pour out as much as you can use per coat as it will set on you if you leave it in an open cup. Re: applying permagloss - additional question
Posted by:
Steve Rushing
(---.asm.bellsouth.net)
Date: February 03, 2003 11:24PM
Thanks. I think I'll make one batch and quickly transfer to some small bottles I have and seal. And, as you suggest only open what I need and re-seal. Re: applying permagloss
Posted by:
lorenzo tellez
(---.hsd1.il.comcast.net)
Date: June 23, 2010 10:50PM
after the first wipe with permaglass. how do you store the permagloss for the next coat? and so mix the pigment in the bottle? I have 1oz bottles. Re: applying permagloss - additional question
Posted by:
lorenzo tellez
(---.hsd1.il.comcast.net)
Date: June 30, 2010 08:08AM
TO: Ed, How much pigment or paint would u need to put in the permagloss, to do an entire rod? Sorry, only registered users may post in this forum.
|