SPONSORS
2024 ICRBE EXPO |
thinning epoxy
Posted by:
Kevin Bergeron
(---.no.no.cox.net)
Date: February 27, 2011 02:08PM
Can flex coat epoxy be thinned and still be effective? I need to get epoxy through a syringe to repair a cork handle that is turning a bit where it meets the real seat, but I cant seem to find an epoxy thin enough. Thanks Re: thinning epoxy
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: February 27, 2011 02:13PM
Devcon at Home Depot Bill - willierods.com Re: thinning epoxy
Posted by:
Phil Ewanicki
(---.135.188.72.cfl.res.rr.com)
Date: February 27, 2011 02:20PM
The easiest way I know of to thin epoxy is to heat it. Re: thinning epoxy
Posted by:
Kevin Bergeron
(---.no.no.cox.net)
Date: February 27, 2011 03:04PM
Bill, any particular product they sell Re: thinning epoxy
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: February 27, 2011 03:18PM
Devcon is the name of the epoxy. It is thinner then rod bond and a lot use it for just the thing you want to do.
You can thin rod bond with lacquer thinner medium temp thinner but I am not sure how it will set in a closed area ? The last one I did I was lucky to remove the hook keeper and get the seat to move forward about 2-3 " Then I cleaned all the old epoxy off and re epoxied it. Bill - willierods.com Re: thinning epoxy
Posted by:
Clyde Dent
(---.lightspeed.ltrkar.sbcglobal.net)
Date: February 27, 2011 04:47PM
On occasion, I thin it with xylol. Just a few drops from a clean eye dropper. No problems.
Clyde Dent Re: thinning epoxy
Posted by:
Kevin Bergeron
(---.no.no.cox.net)
Date: February 27, 2011 05:47PM
What about CA glue for the repair? It is not the whole grip that turns but the top half inch. Re: thinning epoxy
Posted by:
Bob Balcombe
(---.ka.centurytel.net)
Date: February 27, 2011 07:30PM
What type of syringe are you using? I would go to a Veterinarian and get one they shot horses and cows with Remember epoxies dry by a chemical reaction and not air. Why not cut the cork away, clean out the area all the way around, let set. Then replace the cork. You can do the whole process in less than 20 minutes. I done correctly no one well ever know. I have given seminars on this system in the past. I also use this method when I need to repair damage cork. Email me if you want the directions Good Wraps Bob Re: thinning epoxy
Posted by:
Kevin Bergeron
(---.no.no.cox.net)
Date: February 27, 2011 10:11PM
Thank you Bob, I sent you an email. Re: thinning epoxy
Posted by:
Bill Eshelman
(---.skylan.net)
Date: February 28, 2011 06:50AM
Bob does a very nice job the way he does it. Since reading his article a few years back I have done two myself and it works just fine
Bill Ohio Rod Builders Canton, Ohio Re: thinning epoxy
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: February 28, 2011 11:00AM
Kevin,
Generally speaking it is in your best interest to NOT try to thin two part adhesives. The solvents, thinners or diluants, will often have an effect of the adhehesive finish. Often the adhesive will turn rubbery, lose strength, or not cure correctly. As some of the others suggested, if you need thinner adhesive, either purchase adhesive that is thinner from the beginning, or use heat to thin the adhesive before application. If you can use one of the other methods listed above , to completely avoid injecting the epoxy, that is even better. Good luck Roger Re: thinning epoxy
Posted by:
Bob Balcombe
(---.ka.centurytel.net)
Date: February 28, 2011 03:04PM
Thanks Bill, It save time and money and if done right know one will ever know. I also use the system when designing a custom cork design, on a already installed cork grip Good Wraps Bob Re: thinning epoxy
Posted by:
Bob Balcombe
(---.ka.centurytel.net)
Date: February 28, 2011 03:07PM
For those interested it can be found on Raymond Adams site
[www.rodbuildingtutorials.com] Just look for Bob Balcombe Good Wraps Bob Re: thinning epoxy
Posted by:
Phil Erickson
(---.dsl.sfldmi.sbcglobal.net)
Date: March 01, 2011 08:58PM
Flex Coat recommends using Acetone to thin. It is printed in their brochure. Not more then 1/4 acetone to the two parts epoxy. Sorry, only registered users may post in this forum.
|