SPONSORS
2024 ICRBE EXPO |
Speeding Up Drying Process
Posted by:
Gabe Nakash
(---.nyc.res.rr.com)
Date: January 08, 2011 07:17PM
I was just wondering if there is anyway to speed up the drying process of my guide and cross wraps without harming the epoxy or wrap etc...
Any and all answers appreciated. Re: Speeding Up Drying Process
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: January 08, 2011 07:22PM
I say don't even try it, but others may chime in with options. Re: Speeding Up Drying Process
Posted by:
Tom Kirkman
(Moderator)
Date: January 08, 2011 07:23PM
You can speed the set and cure time of your epoxy by increasing the room temperature. No need to over do it, however. Whatever the time currently required to set and cure your epoxy at 70F, can be cut in half by raising the temperature to 90F. Somewhere in-between will result in something in-between.
...................... Re: Speeding Up Drying Process
Posted by:
Greg Foy
(---.dsl.snfc21.pacbell.net)
Date: January 08, 2011 07:39PM
You can point a lightbulb at it. Re: Speeding Up Drying Process
Posted by:
Gabe Nakash
(---.nyc.res.rr.com)
Date: January 08, 2011 08:20PM
Thanks guys. I dont wanna take any chances though because its on of my first set of rods. Re: Speeding Up Drying Process
Posted by:
Fred Yarmolowicz
(---.hsd1.nj.comcast.net)
Date: January 08, 2011 10:18PM
Even the heat from a light bulb can shorten the cure time. Freddwhy (Rapt-Ryte) Re: Speeding Up Drying Process
Posted by:
lee smith
(---.hsd1.ms.comcast.net)
Date: January 09, 2011 09:19AM
I know this being your first, you really want to get it done and get it done NOW! Been there, done that!!
My thought is leave it alone, 70 degree room and let her spin. Hurrying a "custom" job is not the way to go. It will be great and you will definately smile when you get up in the morning!! JMHO Lee Re: Speeding Up Drying Process
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: January 09, 2011 09:35AM
lee smith Wrote:
------------------------------------------------------- > I know this being your first, you really want to > get it done and get it done NOW! Been there, done > that!! > > My thought is leave it alone, 70 degree room and > let her spin. Hurrying a "custom" job is not the > way to go. It will be great and you will > definately smile when you get up in the morning!! > > JMHO > > Lee I agree and think we've all probably been in that boat, sometimes with an adverse effect also. Re: Speeding Up Drying Process
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: January 09, 2011 10:13AM
if it messes up it will cost you twice the amount of time. Bill - willierods.com Re: Speeding Up Drying Process
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: January 09, 2011 11:31AM
Gabe,
Turn the heat up to the top in the drying area and it will shorten the time. If you have a space heater, just turn on the space heater and shut the door to the drying room. Roger Re: Speeding Up Drying Process
Posted by:
Bruce Tomaselli
(---.altnpa.east.verizon.net)
Date: January 09, 2011 04:57PM
Yep, I turn on a space heater in the room I'm working in and it gets the temps up to about 75 or 80. The normal temperature in the room is only about 63. I don't worry about shortening the drying time. I've been getting a good result with this method and I'm not changing a thing. One thing for sure I found out about finishing is that once you get a consistent finish don't change a thing. My shortcuts always caused me problems. But that's just me. Re: Speeding Up Drying Process
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: January 09, 2011 09:57PM
I like to put it on in cooler temps. Then when it is all covered I shut all the doors and windows and let it warm up.
Just let it do it's thing. Don't load it on, several light coats is better then one heavy coat. Bill - willierods.com Re: Speeding Up Drying Process
Posted by:
Todd Badgley
(---.hsd1.tn.comcast.net)
Date: January 09, 2011 11:48PM
I can't remember the vendor's name at last year's ICRBE, but he had an oven that would instantly cure any thread finish. Seemed to work great, but a little pricey.
Maybe Tom can help, he was the vendor with the high quality cork from South America. Sorry, only registered users may post in this forum.
|