SPONSORS
2024 ICRBE EXPO |
Perma Gloss how to?
Posted by:
Ryan Thirtyacre
(---.dr01.aled.il.frontiernet.net)
Date: August 20, 2010 06:52PM
i am looking to make some threadless wraps using perma gloss... i was just wondering what the proper way to do this was. i plan on using micros. and thats about it. any help would be great guys.
thanks, ryan Re: Perma Gloss how to?
Posted by:
Tom Kirkman
(Moderator)
Date: August 20, 2010 07:35PM
RodMaker Volume 9 #6 for the full and complete details, or you can glean what you can from the internet and hope for the best. Far too much for a message board post.
Do a search here for past discussions on the topic. I'm sure you'll also get some additional posts with further information. .................... Re: Perma Gloss how to?
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 20, 2010 07:46PM Re: Perma Gloss how to?
Posted by:
Rolly Beenen
(---.cpe.net.cable.rogers.com)
Date: August 20, 2010 07:53PM
So Bill how did that help. A pile of posts on PG but not answering the question. Rolly Beenen Rovic Custom Rods Re: Perma Gloss how to?
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 20, 2010 07:56PM
How many of them did you read ????
Many builders put it on in different ways Do a search of - thread-less guide wraps Also white silk can be a thread less wrap It disappears.--- Under epoxy here are some photos [www.rodbuilding.org] Bill - willierods.com Edited 4 time(s). Last edit at 08/20/2010 08:28PM by bill boettcher. Re: Perma Gloss how to?
Posted by:
Jeremy Wagner
(---.hsd1.de.comcast.net)
Date: August 20, 2010 08:06PM
Rolly, I burst out laughing when I read your post. Irony...
Ryan, the best advice is to get the Rodmaker mag that covered it. jeremy Re: Perma Gloss how to?
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: August 20, 2010 08:08PM
Ditto Bill - willierods.com Re: Perma Gloss how to?
Posted by:
Tom Kirkman
(Moderator)
Date: August 20, 2010 08:25PM
A silk wrap is a transparent wrap, but thread is still involved. The PG method is a true threadless wrap. It just depends on what you're after.
................ Re: Perma Gloss how to?
Posted by:
Lance Dupre
(---.mycingular.net)
Date: August 21, 2010 03:36PM
He did say threadless wraps. Permagloss is used to adhere the guides to the blank. If you don't buy the magazine detailing the process you will waste a lot of time and probably a few extra bucks trying to figure it out on your own. Do yourself a favor and buy the magazine and do it right the first time. All of those posts on permagloss will get you nowhere and probably frustrate you to no end. Lance Re: Perma Gloss how to?
Posted by:
Ryan Thirtyacre
(---.dr01.aled.il.frontiernet.net)
Date: August 21, 2010 09:10PM
well looks like im getting the magazine... Re: Perma Gloss how to?
Posted by:
Bill Napier
(---.astrahosting.com)
Date: August 21, 2010 09:29PM
You are going to be getting a lot more than just a "magazine." Wait and see...... you are going wonder how much you have missed by not taking this all along. That same issue is going to teach you so many other things too. Anyone that is really serious about rod building gets a huge benefit from the magazine. it's the cutting edge. Re: Perma Gloss how to?
Posted by:
lorenzo tellez
(---.hsd1.il.comcast.net)
Date: August 23, 2010 05:51PM
Does anyone know if the threadless wrap will work on those micro guides like size 2mm? Re: Perma Gloss how to?
Posted by:
Tom Kirkman
(Moderator)
Date: August 23, 2010 06:56PM
Yes. But read the article - there are certain limitations.
............. Sorry, only registered users may post in this forum.
|