SPONSORS
2024 ICRBE EXPO |
Renzetti Rod Support "O" rings
Posted by:
Steve Burdick
(---.skybeam.com)
Date: March 09, 2010 08:35AM
My Renzetti rod support "O" rings are beginning to crack and I need to replace them. Is there anyplace other than Renzetti to buy these. I have tried my local ACE Hdw. store, auto parts and so on, with no success. I looked at Renzetti's site and found them for $2.00 each, but the shipping was $18.00 for 9 "O" rings. Seems a bit high to me (shipping). Any one have any ideas or suggestions? Any and all would be appreciated.
Thanks in advance Steve Burdick It only costs pennies more to be first class Re: Renzetti Rod Support "O" rings
Posted by:
Walt Davenport
(63.97.59.---)
Date: March 09, 2010 08:42AM
call renzetti, they will ship them usps (at a significant saving)if you ask; or at least they have for me in the past Walt Davenport "Roadhouse Rods" Re: Renzetti Rod Support "O" rings
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: March 09, 2010 08:46AM
Try Mud Hole. They carry spare parts Bill - willierods.com Re: Renzetti Rod Support "O" rings
Posted by:
Chuck Payne
(---.cable.mindspring.com)
Date: March 09, 2010 08:55AM
Billy Vivona of the NERBS did have them, and the nice Viton ones also, which are better than what came on it , shoot him an email Re: Renzetti Rod Support "O" rings
Posted by:
Billy Vivona
(---.nycmny.east.verizon.net)
Date: March 09, 2010 09:04AM
I sold out of mine after that last post. Re: Renzetti Rod Support "O" rings
Posted by:
Lou Wasmund
(---.sd.sd.cox.net)
Date: March 09, 2010 09:52AM
Try a hydraulic supply shop. They should have quite a selection of o-rings Re: Renzetti Rod Support "O" rings
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: March 09, 2010 10:26AM
Steve,
What is the diameter of the spool on which the O ring is placed. What is the diameter of the unstretched O ring - i.e. the actual size of the piece of unstretched rubber? If you post these, we can then give you a source for a replacement ring. Take care Roger Re: Renzetti Rod Support "O" rings
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: March 09, 2010 10:42AM
Steve,
You indicated that you were not able to find the O ring that you needed at your local hardware store. I would suggest that you take your rod rest off your lathe, and take it with you to the next trip to the hardware store, and use it to snap on one of the many many different O rings that most good hardware stores have in their plumbing department. Just because an O ring is not the same size as the resting size of the O ring that you took off the rod rest does not mean that there is not another one out there - of a close and or similar - but not the exact same size that worn't work just as well. Take care Roger Re: Renzetti Rod Support "O" rings
Posted by:
Andy Cichon
(---.nyc.biz.rr.com)
Date: March 09, 2010 12:16PM
try oringusa.com Re: Renzetti Rod Support "O" rings
Posted by:
mike harris
(---.borgwarner.com)
Date: March 09, 2010 12:52PM
Here is a chart that shows standard AS568A o-ring dash sizes, there is no chance that they are using anything other than a standard o-ring.
[www.allorings.com] Once you figure out which dash number you need you can probably buy a bag of 100 for about 10 bucks. Re: Renzetti Rod Support "O" rings
Posted by:
kevin knox
(---.baybroadband.net)
Date: March 09, 2010 01:22PM
Your local hydraulisc shop has them. They are standard orings. Look in the yellow pages and tell them you need orings for code 61 split flanges.
KK Re: Renzetti Rod Support "O" rings
Posted by:
kevin knox
(---.baybroadband.net)
Date: March 09, 2010 01:24PM Sorry, only registered users may post in this forum.
|