SPONSORS
2024 ICRBE EXPO |
curing thread finish
Posted by:
Andy Jones
(---.gsp.bellsouth.net)
Date: December 31, 2009 12:10AM
Out of curiosity, how does everyone cure their thread finish? Turn by hand for a while and place in a dryer, apply finish and place in dryer, or are you a hand turner only. If you have any other methods I sure would like to hear them. Edited 1 time(s). Last edit at 12/31/2009 06:24AM by Andy Jones. Re: cuing thread epoxy
Posted by:
Phil Brenner
(198.217.64.---)
Date: December 31, 2009 03:36AM
i have always applied the epoxy then put in the dryer and walked away. Just for giggles i tried hand turning untill semi set (probably 45 min or so) and then putting in the dryer. I think it came out better that way. Im going to do it that way from now on. I seemed to get a more level finish this time. who knows could be a fluke, but im going to experiment for sure Re: curing thread finish
Posted by:
Matt Davis
(---.prtel.com)
Date: December 31, 2009 07:17AM
In a heated drying box. I run it at about 90°.
................... Better to have and not need than to need and not have. Re: curing thread finish
Posted by:
Tom Kirkman
(Moderator)
Date: December 31, 2009 08:43AM
By hand, turning a full 180 degrees only when needed.
.............. Re: curing thread finish
Posted by:
Fred Yarmolowicz
(---.hsd1.nj.comcast.net)
Date: December 31, 2009 09:13AM
I hand turn for the first 45 min if possible on a decorative wrap and look for sags and remove. Then put in on the drier with my magnifying light over it to generate a little heat. I monitor the temp with a digital thermometer with a memory. Usually stays around 70 . Guide wraps I hand turn to remove excess finish and into the drier it goes. Key is not to leave too much finish on the wrap for it to be level. Freddwhy (Rapt-Ryte) Re: curing thread finish
Posted by:
Pat Helton
(---.dhcp.embarqhsd.net)
Date: December 31, 2009 09:32AM
I usually don't have time to hand turn so I put it on the dryer at room temp. and leave it until it has set up completely. I am carefull about measuring and mixing, I don't overload with finish, and I don't put on a second coat unless I have areas that aren't covered well. It's been working for me for about twenty years.
Pat Re: curing thread finish
Posted by:
J.B. Hunt
(---.pool.dsl.logantele.com)
Date: December 31, 2009 10:46AM
I do the same as Pat Helton. Works for me too. J.B.Hunt Bowling Green, KY Re: curing thread finish
Posted by:
Victor Heal
(---.gdrpmi.dsl-w.verizon.net)
Date: December 31, 2009 11:49AM
Same as Pat and Jay.
Several light coats one at a time. Put finish on, and onto the dryer. If I am covering a long area ie. butt wrap, feather inlay etc. then I will turn the drums on my dryer a little offset from eachother. I think it helps to level out the finish a bit. The key for myself is light coats. Vic Re: curing thread finish
Posted by:
Terry Turner
(---.hsd1.or.comcast.net)
Date: December 31, 2009 01:22PM
I'll hand turn to apply finish to a butt wrap area, just until it is evenly spread, which means I've gone through the sag and wick off the bottom a few cycles, then it goes on the dryer.
Terry Re: curing thread finish
Posted by:
Phil Erickson
(---.dsl.pltn13.sbcglobal.net)
Date: December 31, 2009 05:17PM
I'm also one who applies by hand, then the 180 degree turns to wick off sags, then onto my power drying turner. Re: curing thread finish
Posted by:
Gary Henderson
(---.mco.bellsouth.net)
Date: January 03, 2010 01:13PM
Yep...same as Phil. Apply the finish, rotate the rod by hand 180 degrees for the first hour or so, removing any excess finish with a credit card, then into the drying motor/chuck/stand until it is no longer tacky. Sorry, only registered users may post in this forum.
|