SPONSORS
2024 ICRBE EXPO |
micro guide supplier...
Posted by:
Trinity Lindseth
(---.ips.PaulBunyan.net)
Date: February 05, 2009 10:04PM
Where would you all recommend I purchase a few sets of micro guides from? I have a couple blanks to wrap and want to give the micro guides a try. I plan to spiral wrap both blanks, and will probably use the quick transition to the bottom of the blank. Would an 8 as the first guide work with a 4 as a bumper between the transition guide and the first on the bottom, probably use a 6 for the first on the bottom, then 3's the rest of the way out to the tip be a good set up? Would it work if I started with a 6 instead of an 8? I want to use as small of guides as possible. Thank you for the suggestions in advance. Re: micro guide supplier...
Posted by:
Duane Richards
(---.rn.hr.cox.net)
Date: February 05, 2009 10:13PM
Bob at Custom Tackle Supply on the left in the sponsor section.
I like an 8mm as a stripping guide (first guide from reel), then go down from there, I have used a 6mm but I like the height of the 8mm better..... and yes your 4mm will work as it's only use will be to keep line off the blank in the bumper method. DR Re: micro guide supplier...
Posted by:
Lance Dupre
(---.hsd1.la.comcast.net)
Date: February 05, 2009 10:14PM
I have them in stock. Here's the link to the page.
I like to use a no. 6 double ft guide then a no. 5.0 micro, then a 4.0 micro and six 3.5 micros as my 180 degree guides. [www.swamplandtackle.com] Lance Re: micro guide supplier...
Posted by:
bill boettcher
(---.mis.prserv.net)
Date: February 06, 2009 12:43AM
Why not use the 3 as the bumper, all you are doing is keeping the line off the blank. Bill - willierods.com Re: micro guide supplier...
Posted by:
George Forster
(71.237.22.---)
Date: February 06, 2009 10:51AM
Hi Trinity,
I would suggest getting sz 6, 8, and 10 for possible butt guides, and 4, 5, 6 as possible bumpers. You will need to set everything up (with tape or rubber bands or zip ties) to see what works with your blank and reel (reel seat and handle already glued in place). Check your line flow, and do some test casting. Smaller butt guides need to be further from the reel to get good line flow. You may need a bigger butt guide to clear a fore grip. If you have a large diameter blank, you may need a bumper bigger than a 4 to keep the line off the blank (assuming you're doing a simple spiral). There are many variables to consider. A few extra guides ordered initially will save you headaches and shipping charges later. Plus, you'll end up with some extra guides for a future rod or testing. George Re: micro guide supplier...
Posted by:
Tom Kirkman
(Moderator)
Date: February 06, 2009 10:56AM
You do not want to use a too small ring for the bumper guide if the rod is expected to flex well into the butt section. You don't want any side load on the bumper guide and thus a larger ring in a low frame (bent/shaped even lower) is your best bet for use as a bumper guide. The line may need a bit of leeway in that area if you expect a full flex in the butt section. Generally a size 8 is sufficient.
................... Re: micro guide supplier...
Posted by:
Trinity Lindseth
(---.redlake.k12.mn.us)
Date: February 06, 2009 11:17AM
Are the guides form Swampland and Custom tackle th esame guides? I can't seem to find them on the CT site... Re: micro guide supplier...
Posted by:
BobMcKamey
(---.united.net)
Date: February 06, 2009 11:47AM
We carry the Micro guides in three different frame and ring configurations from Batson Enterprises and three different frame and ring configurations from Fuji. Give me a call at 931-684-6164 and I be glad to discuss the various Micro guides we offer.
Bob McKamey -- Custom Tackle Supply Sorry, only registered users may post in this forum.
|