SPONSORS
2024 ICRBE EXPO |
RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Mark Ekstrand
(---.hbci.com)
Date: April 29, 2006 05:59AM
Hi folks!
I'm trying to place an order with Rocky Mountain Rodbuilding to replace a Dan Craft Five Rivers FT rod blank tip section that met an untimely demise recently. I bought the blank from Rocky, like their products and would like to continue doing biz with them but am unable to find someone there to help me out. Anyone have contact info? thanks, Mark PS: the FT908-4 blank is one powerful rod for pike. Like the ad says, "It's an 8 wt. that thinks it's a 10". Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Shawn Moore
(85.195.123.---)
Date: April 29, 2006 08:02AM
They were once a sponsor here but got removed because of all the complaints lodged against them. I think. Just be careful and do NOT pay up front.
I think you can order direct from Dan. That might be the smarter move. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
bill boettcher
(---.nas97.newark2.nj.us.da.qwest.net)
Date: April 29, 2006 08:13AM
Email Dan. You will have a lot better luck. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
bill boettcher
(---.nas97.newark2.nj.us.da.qwest.net)
Date: April 29, 2006 08:14AM
Email Dan. You will have a lot better luck. When he finishes his site you will be able to order right from it. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Wayne Kohan
(---.dhcp.knwk.wa.charter.com)
Date: April 29, 2006 10:37AM
I've e-mailed Dan twice, once off his site and once off this board, and I have yet to get a response from him. I have found that Rocky Mountain site and noticed they seemed cheaper than where I usually order from, but if they have bad business habits, then I won't order from them. But then, where do I get a Dan Craft blank?
Wayne Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Jan Podsiedlik
(---.ed.shawcable.net)
Date: April 29, 2006 10:41AM
I don't know whats going on at Rocky but I can tell you about my experience. I ordered a number of items from them over a year ago, they shipped what they had in stock ... and forgat all about the remaining (and paid for) items which included RX7+ blank and a nickel silver seat. After straightening everything out, I gave them the benefit of the doubt and placed a second order with them. Unfortunately the result was pretty much the same and I'm still waiting for a few items, including the nickel silver seat from the original order. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
bill boettcher
(---.250.165.161.Dial1.Weehawken1.Level3.net)
Date: April 29, 2006 11:09AM
Dan probably went fishing ?? LOL Try to call and leave a message. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Spencer Phipps
(---.lsil.com)
Date: April 29, 2006 12:52PM
Dan has had a big spam problem in the past and filters his incoming emails. I just call him anymore, he does get back to me via email, but it's usually a few days later. Also he was working a "swing shift" schedule at the shop to coincide with his wife's schedule, and to probably get some fishing in during the short winter months. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Bob Crook
(---.an2.sea18.da.uu.net)
Date: April 29, 2006 01:05PM
What email address are you using for Dan? I use: danfisherman@earthlink.net and have never had any problem getting ahold of him, however as others have stated the phone is the best way. Re: RockyMountain Rodbuilding rep for Dan Craft blanks?
Posted by:
Wayne Kohan
(---.dhcp.knwk.wa.charter.com)
Date: April 29, 2006 02:52PM
Thanks, I'll try the phone. I'm excited to try out his blanks.
Wayne Thanks for the info, guys!
Posted by:
Mark Ekstrand
(---.hbci.com)
Date: April 30, 2006 02:45AM
Thanks alot, guys, you've all been great.
BTW, any place else sell Five River blanks beside Dan Craft? He's a pretty busy guy and have had problems getting through as well. Will try the phone, though. thanks again. Mark Sorry, only registered users may post in this forum.
|