SPONSORS
2024 ICRBE EXPO |
Website Update
Posted by:
Andy Dear
(---.231.14.197.Dial1.Houston1.Level3.net)
Date: February 02, 2006 04:23PM
Ok guys, it seems that were now back up and running at full capacity. I have made some changes to the site for better performance, and also to betetr reflect what we do down here in South Texas.
First of all, the website address has changed. It is now www.lamarfishing.com The lamarreelseats address will remain active for a few months, but eventually it will go away, so update your "favorites list" with the new address! Also, my email is now andy@lamarfishing.com I am doing my best to catch up on all the rogue emails flaoting around in my old inbox, so please be patient! REgards, Andy Dear Lamar Manf. www.lamarfishing.com Re: Website Update
Posted by:
Randy Parpart (Putter)
(---.nccray.com)
Date: February 02, 2006 04:37PM
Rogue? I didn't know you dealt with those, Andy? ;) Putter Williston, ND Re: Website Update
Posted by:
bill boettcher
(---.nj-01.cvx.algx.net)
Date: February 02, 2006 06:30PM
Andy
You and Karen at Bingham the only ones that carry Thread Master ?? Re: Website Update
Posted by:
Andy Dear
(---.231.14.95.Dial1.Houston1.Level3.net)
Date: February 02, 2006 07:05PM
No,Angler's Workshop does as well, and there MAY be 2 other distributors added as well. Ross Van Eckenvort In Australia has signed on as the Australian Distributor, and I just sent samples to a supplier in Spain today.
Although I am the master distributor with the sole exclusive rightsto the chemistry, I completely understand many of you prefer to buy from a certain vendor for certain reasons, therefore I encourage you to buy from any of the fine folks we partner with. I wouldn't have become involved with them if I didn't trust their integrity 100% Andy Re: Website Update
Posted by:
bill boettcher
(---.nj-01.cvx.algx.net)
Date: February 02, 2006 07:19PM
I will buy from who ever ? I just under stand that you are have delivery problems and Karen must be busy and hard to get in touch with. Re: Website Update
Posted by:
Andy Dear
(---.231.14.21.Dial1.Houston1.Level3.net)
Date: February 02, 2006 08:45PM
I am having delivery problems? Not that I am aware of......my email has been goofy these past few weeks, but that is fixed.
No delivery problems here...I have shipped over 60 orders this week. Andy Dear Lamar Mfg. Re: Website Update
Posted by:
bill boettcher
(---.nj-01.cvx.algx.net)
Date: February 02, 2006 09:02PM
I thought that email and site thing was slowing you down ? Your getting an email. Thanks Re: Website Update
Posted by:
John Blair
(---.rgv.res.rr.com)
Date: February 02, 2006 10:08PM
Andy,
I will re-send all my emails...........Thanks for the info.........I was getting worried not hearing from you Big John Rio Hondo, Texas Blessed are those who can give without remembering and take without forgetting Re: Website Update
Posted by:
Raymond Adams
(---.hsd1.ca.comcast.net)
Date: February 02, 2006 10:13PM
Hi Andy,
Just looked at the new site and saved it! GOOD JOB! Raymond Adams Eventually, all things merge, and a river runs through it.. Re: Website Update
Posted by:
Galen Briese
(134.129.79.---)
Date: February 03, 2006 11:51AM
Andy, I am curious about the reamer setup that you are developing. I checked the website and it doesn't show up there, but any how I would like to hear more, and the approximate cost. Also, I would like to try out your new finish, but it is butt cold up here in North Dakota and guess that I will have to wait until it warms up before I get some, unless there is an alternative method of getting here without freezing. Thanks Galen Briese Re: Website Update
Posted by:
Andy Dear
(---.231.14.71.Dial1.Houston1.Level3.net)
Date: February 03, 2006 05:33PM
Galen,
Just sent you an email regarding the freezing of epoxy.... Andy Sorry, only registered users may post in this forum.
|