SPONSORS
2024 ICRBE EXPO |
JB Weld
Posted by:
Ron Hossack
(---.61.105-203.ptr.llix.net)
Date: September 18, 2005 11:19AM
I need to glue a ferrel back on a bamboo rod that came loose and don't trust
my 5 minute epoxy due to the slop after cleaning it up, Has anyone used JB Weld before and if so is this a good alternative? Re: JB Weld
Posted by:
Stan Grace
(---.hln-mt.client.bresnan.net)
Date: September 18, 2005 11:24AM
I have had good success with JB Weld for other purposes but I would use Rod Bond for the ferrule if I had it available. Stan Grace Helena, MT "Our best is none too good" Re: JB Weld
Posted by:
Ron Hossack
(---.61.105-203.ptr.llix.net)
Date: September 18, 2005 12:38PM
Stan Grace Wrote:
------------------------------------------------------- > I have had good success with JB Weld for other > purposes but I would use Rod Bond for the ferrule > if I had it available. Thanks Stan ... problem is I don't have any rod bond handy as most of my stuff is in storage. I do have some 20 minute epoxy and the JB Weld. Maybe I should just order some ... need some stuff from Andy Dear so I might as well place another order. Re: JB Weld
Posted by:
Anonymous User
(Moderator)
Date: September 18, 2005 01:12PM
Products are only as good as their intended useage. JB Weld was created for plugging cracks and gaps in fuel tanks, metal hose or fuel lines, structure ruptures, etc. You'll be better off using regular liquid epoxy over the JB Weld. RodBond would be even better if you have the time to pick some up.
........... Re: JB Weld
Posted by:
larry pirrone
(---.ontrca.adelphia.net)
Date: September 18, 2005 03:41PM
actually very few bamboo builders use rod bond for setting ferrules but some swear by JB weld. i have used it to set ferrules on bamboo and it has held up well. some use a hot melt ferrul cement, and quite a few builders also use pliobond. Re: JB Weld
Posted by:
larry pirrone
(---.ontrca.adelphia.net)
Date: September 18, 2005 03:51PM
HER IS AN ANSWER FROM A BAMBOO ROD FORUM:
Forget epoxy for ferrule work. Clean the inside of the ferrule and the cane. Use Pliobond cement. With a Q-tip, apply 1 coat to the inside of the ferrule. Apply a coating to the cane. Let that dry and apply a second coating to the cane. Let that coating dry also. Start the ferrule as far as it will go by hand, Apply heat to the cement and ferrule and press the ferrule on untill it is completly seated. This may take a good bit of effort. Clean the excess with MEK, wrap if necessary, and touch up the varnish. Good for many year of fishing. Re: JB Weld
Posted by:
Ralph O'Quinn
(---.wavecable.com)
Date: September 18, 2005 08:08PM
Here is my answer to the Bamboo Rod Forum
There is no technology under the sun more UNSUITED to bond metal to bamboo than Pliobond. I have had many a pow wow with the bamboo types and they are as tradition bound as any group I have ever experienced. The very fact that you join the ferrule to the rod by heating the ferrule and the cement then with a good deal of effort, press the ferrule on until it is completely seated -- tells me that the ferrule would have many years of good service had you used a car wax instead of pliobond for the joint. Of the readily available technologies available to the average rod builder --- the hot melts are probably the best choice for this job as they will stay bonded longer than the epoxies. The epoxies will exhibit the best initial bond strength, but the interface with the metal ferrule will be corroded away in a year or two. However if you are pressing the ferrule on with a good deal of effort --anything you use -- including a good wax -- will do the job, and whatever you use you can point to it and say you have proof positive that this is the best. Ralph Re: JB Weld
Posted by:
larry pirrone
(---.ontrca.adelphia.net)
Date: September 18, 2005 08:52PM
car wax? hmmmm. cheap enough thats for sure. many bamboo rod builders don't like epoxy and some swear by it. but i think you are right ralph. the hot melts are the best idea i think. Re: JB Weld
Posted by:
Ron Hossack
(---.61.105-203.ptr.llix.net)
Date: September 19, 2005 12:06AM
Ralph O'Quinn Wrote:
------------------------------------------------------- >Of the readily available technologies available > to the average rod builder the hot melts are > probably the best choice for this job as they >will stay bonded longer than the epoxies. By hot melts are you referring to the glue sticks my wife uses in her hot glue gun? Re: JB Weld
Posted by:
Anonymous User
(Moderator)
Date: September 19, 2005 08:31AM
Yes, althought here are different types and heat ranges for those hot melt adhesives.
Now for glueing up our handles and reel seats, you'd want to stick with an epoxy. Ralph is talking about the ferrules used on most bamboo rods. Not the standard seats and grips which we mount on our rods. ................. Re: JB Weld
Posted by:
Ron Hossack
(---.61.105-203.ptr.llix.net)
Date: September 19, 2005 09:02AM
Tom Kirkman Wrote:
------------------------------------------------------- > Yes, althought here are different types and heat > ranges for those hot melt adhesives. > > Now for glueing up our handles and reel seats, > you'd want to stick with an epoxy. Ralph is > talking about the ferrules used on most bamboo > rods. Not the standard seats and grips which we > mount on our rods. Thanks Tom ... I was following what Ralph was saying and it's for a ferrule I need. Sorry, only registered users may post in this forum.
|