SPONSORS
2024 ICRBE EXPO |
Measuring winding check size
Posted by:
Eijiro Kawada
(---.hsd1.wa.comcast.net)
Date: July 06, 2005 10:07PM
I’m an amateur fly-rod builder who builds only a few rods a year, so I don’t have a huge inventory of rod building parts in my drawers. I usually order items online as needed since the closest shop with sufficient rod building parts is more than an hour-drive away. On weekends when I have time to drive to the shops, I would rather be fishing.
One frustration that I always face is figuring out the size of winding checks I need. I always end up putting the reel seat and grip on the blank, and have to take that to a shop to get the correct size winding check. Or, I could measure the diameter of the blank after assembling the reel seat and grip, and order it online. But then, I’ll have to pay $8-$10 for shipping when I only need a winding check, which is $2-$3. I would love to be able to order a correct winding check when I order a reel seat, grip, guides and other things. Any ideas? Can I do away without it? What does a winding check do anyway? Re: Measuring winding check size
Posted by:
Magnus Högberg
(---.handelsbanken.se)
Date: July 07, 2005 03:23AM
I've got the same building freuency as you so i'm familiar with your dilemma.
The retailers i buy from have no problem exchanging small things as guides and WC's if you just send them the WC and includes an envelope with address and postage payed for. I usually give them a call beforehand. This probably depends on where you buy your stuff. //Magnus Re: Measuring winding check size
Posted by:
Paul Dowden
(141.197.12.---)
Date: July 07, 2005 08:19AM
Try using math. Here is what to do:
Diameter at winding check = (X(B-T)/L)+T B = OD at butt T = OD at tip L = Length of rod X = Length from tip to winding check location In words... Subtract the tip OD from the butt OD. Multiply by distance from tip. Divide by total length. Add OD at tip. This should get you close enough. Re: Measuring winding check size
Posted by:
Mike OLiver
(---.proxy.aol.com)
Date: July 07, 2005 11:29AM
Eijiro,
Yes I can relate to your frustration, but it can be cheaper and more time productive to order maybe two or three winding checks to get the right fit. If you have access to a digital vernier or a std one inch micrometer then it should be easey enough to give exact dimensions to your supplier. You ask what is the purpose of winding checks. Well mostly they are there to cover up/ tidy up the ends of foregrips. Many builders ream out their say pr -made fly rod handles and they get bigger holes at the top end of the grip than the OD of the blank. This looks plain ugly so a well sized and chosen winding check covers up this kind of goof. Even if the fit is perfect they can add a lot of asthetic value to a finished rods appearence. They can also if badly chosen in terms of material and size look absolutaly awful to. It's a question of horses for courses. You could consider using a thread winding check, but be careful not to let the high build finish wick up the end of the grip. That does look bad. It's what I use on my salt water fly rods as I no one as yet ismaking Titanium winding checks and I don't want corroding checks on my sticks. I dont like the rubber or plastic variaties. But that is purley a question of preference. If you cant get hold of a vernier or mic then use a decent steel rule and give dimension in fractions of an inch. IF you tyhen order three checks that bracket either side of the rough dimension yopu will be close. Saves having to wait around or spend time sending back low value items. Hope you get it sorted ok. Regards MIke OLiver Re: Measuring winding check size
Posted by:
Billy Vivona
(4.43.114.---)
Date: July 07, 2005 05:06PM
Mike - you can get Fuji Titanium Winding checks from Japan. At least they are in the Fuji Japan catalouge, but that doesn't mean they are actually available. Re: Measuring winding check size
Posted by:
bill boettcher
(---.cvx.algx.net)
Date: July 07, 2005 06:53PM
Maybe one of these will help [shop.mudhole.com] Re: Measuring winding check size
Posted by:
mike Oliver
(---.proxy.aol.com)
Date: July 08, 2005 10:54AM
Billy and Bill,
Thanks. I had to Laugh as usual at your post Billy. I know exactally what you mean when you talk about products in a catalogue but that don't mean they have necassarily ever been made or even released to production. Right now I have $1500 worth of surf rods decked out in Titanium Fuji running guides and awaiting their T tip rings. Sure are in the catalogue but boy I reckon they are virtual rings. If I don't get em soon my virtual customers are going to loose patience. It's a great hobby this. Cheers Mike O Sorry, only registered users may post in this forum.
|