SPONSORS
2024 ICRBE EXPO |
Anyone have a source???
Posted by:
Noel Spann
(12.39.180.---)
Date: November 30, 2004 08:14AM
Does any one have a source for adhesive backed sandpaper to make reamers with, probably 1" - 1 1/2 " wide? My supplier has the paper but its not adhesive backed, I know I can use epoxy or contact cement but just wanted to see what the difference in price would be between the two. Thanks in advance, Noel Re: Anyone have a source???
Posted by:
Dave Barrett
(---.ma.emulex.com)
Date: November 30, 2004 09:27AM
Home Depot sells rolls of it in 3" widths. You can always cut it. Re: Anyone have a source???
Posted by:
bill boettcher
(---.250.57.86.Dial1.Weehawken1.Level3.net)
Date: November 30, 2004 01:56PM
MudHole has the roll just for this Re: Anyone have a source???
Posted by:
eric zamora
(216.101.134.---)
Date: November 30, 2004 02:53PM
have you explored the possibility of using loose grit epoxied or glued to a blank section? eric fresno, ca. Re: Anyone have a source???
Posted by:
Bob Balcombe
(---.rb.gh.centurytel.net)
Date: November 30, 2004 04:19PM
All the above ideas are great. One thing you have to watch out for is grit coming loose and impregnating in to the cork. The grit well act as a abrasive and could cause blank failure. I use metal reamers Good Wraps Bob Re: Anyone have a source???
Posted by:
bill boettcher
(---.250.57.163.Dial1.Weehawken1.Level3.net)
Date: November 30, 2004 06:29PM
Like said, you are better off with the tape Re: Anyone have a source???
Posted by:
David A. Fuller
(---.NIPR.MIL)
Date: November 30, 2004 06:32PM
Mudhole and Grizzly tools David A. Fuller Great Basin Fishing Rods Re: Anyone have a source???
Posted by:
Ed Carr
(---.msn.com)
Date: November 30, 2004 09:31PM
I made grit reamers and they don't lose grit, maybe first time I used them but I check and there are no bare spots. I ream awhile then clean with fox tail brush to get cork out of grit. Frankly I'm surprised they hold up so well. ED... Re: Anyone have a source???
Posted by:
Randy Parpart (Putter)
(---.nccray.com)
Date: December 01, 2004 01:18AM
I'm still using the grit reamer I made over 20 years ago. I do everything by hand with it. I don't know how it would hold up to a power drill, though. Putter Re: Anyone have a source???
Posted by:
Mark Schulte
(---.tnt1.valparaiso.in.da.uu.net)
Date: December 01, 2004 02:47AM
I got a kit from Custom Tackle a few years ago. A few short scraps of various dia. blanks and a roll of heavy grit 1/4 - 1/2 wide sand paper/cloth. use contact cement or 3M weather strip adhesive to bond the cloth to the blanks ,and been going strong for years. Re: Anyone have a source???
Posted by:
Kit Harrison
(---.txucom.net)
Date: December 01, 2004 06:30AM
Putter I use mine in a variable speed battery operated drill and have never had a failure. The only time I had any problem at all was when I tried the drill on high speed and it heats up to quick. So I learned to just use it at lower speeds. Sidewinder Sorry, only registered users may post in this forum.
|