Is it advisable to use Pro Wrap Metallic thread for the entire guide wraps from butt to tip or should it only be used sparingly for trim bands or inlays????Thank you for any information in advance.
Forum: rodboard

I have a question about a G2 Carbon Handle 12" Full Length Casting Grip...this grip was chosen by a customer....I am fairly new to the rod building obsessive behavior and this is the first full length carbon handle I have installed.....am I assuming correctly this grip has arbors on both ends and only the ends need Pro Paste or should I apply Pro Paste to the blank for the full length of the
Forum: rodboard

Peter......CRB Color blanks might be an option....I have built on several of them for charity purposes. They are light and not to expensive.
Forum: rodboard

Nothing wrong with a MHX 845CB 7'0
Forum: rodboard

I chose to use Acetone on a paper towel and I believe I was successful....clear finish is not tacky nor did the acetone cloud the clear base coat.....all that remains is to apply the decal properly this time, put second coat over it and cross my fingers. I want to thank everyone for their input on this issue. This forum is unbelievably terrific for information in this obsessive, compulsive hobb
Forum: rodboard

I pulled the decal off by getting a fingernail under a corner and then very slowly pulled the decal off by folding the decal over the top of itself. Like I thought there was some adhesive left behind....I then used friction from my thumb to remove adhesive....then a wet paper towel under my thumb...followed by dry paper towel under my thumb...then finally the polishing cloth that came with the
Forum: rodboard

just clear thread finish under the decal...no thread....and no finish over the decal....are you better off when you have to remove a decal if you have applied the decal to a bare blank?
Forum: rodboard

I have a MHX rod peel and stick spec decal that I applied and it looks horrible.....I would like to remove it......decal is applied on top of Pro Kote thread finish that was allowed to cure for 24 hrs. Have not put a second coat over the decal. What would be suggested to remove it without harming the base thread finish?
Forum: rodboard

THANK YOU Mark, Tom, and Joe.....Tom..while never having before worked with Color Preserver, I have some ordered.....Joe, thanks for your tip, I believe you have posted that before, it is bound to help.....Mark, I have your suggestion in my back pocket, if I fail with the color preserver, I will order some custom decals... Thanks again for your responses!!
Forum: rodboard

I have a customer who would like a HS Mascot sticker on their rod I built.....problem is the sticker the customer supplied is not vinyl or plastic, it has some paper qualities to it and the edges of the customer's decal wants to curl up after the Pro Kote finish goes over it. Any suggestions ??? Super glue?, forget about it?, try to have one made out of vinyl or plastic?? Thanks in advance for
Forum: rodboard

Mudhole sells CRB marbling pigment in several colors....other sponsors on this site may very well do the same...I have used CRB Marbling pigment with success. A single 1 ounce jar might be a lifetime supply !! You must use sparingly, a little bit goes a long way. In one of Mudhole"s Facebook Live Videos ( I believe the video on Marbling) they spend some time using the marbling pigments.
Forum: rodboard

Help!!!!!! Looking for a 2 Piece spinning application blank for a customer.....6'0 or 6'6....MH....MF....10-17 lb.......Customer says 2 piece #1 priority, durability is Number 2.....Med. heavy #3......$50-$150 price range. THANKS in advance.
Forum: rodboard

I'm not an expert, but Is it possible experienced custom rod builders like Mr. Kirkman might even prefer the blank to bend a little, so you can place the guides on the upward slant to increase power and lift capacity as opposed to a perfectly straight blank??
Forum: rodboard

How often do you need the inserts on CCT casting rod seats ? Either the Blade or the Razor ?
Forum: rodboard

Thank you Norman..
Forum: rodboard

Would anyone on this board consider trimming 2-4 inches of the butt end of the NFC MB 765 or would you just get the NFC SJ 736? Will be using 5/16 oz. to 1/2 oz. weights and Beaver style plastics. Fishing from a mini bass boat....afraid 7'6 is too long of a rod.
Forum: rodboard

I want to THANK everyone who has responded, all information is valuable to me....the knowledge that this forum has is a terrific benefit to those of with lesser rod building knowledge. Thanks again, to all of those that have responded, I am sincerely appreciative for your sharing of your expertise.
Forum: rodboard

I would like for it to take on the same color as the blank....So I guess maybe I am wanting to get a translucent look vs transparent...it maybe necessary to get thread the same color as the blank...I'm not experienced enough to know for sure..
Forum: rodboard

Probably discussed before....I'm a rookie, I've built about 8 rods...always used color fast thread, getting ready to thread wrap guides on a Metallic Blue MHX blank....from what I know....If I am using White Pro Wrap Nylon non color fast size A thread......it will take on the color properties of my blank...Is that true???? I'm thankful and appreciative of any advice. Just want to make sure bef
Forum: rodboard

Rodgeeks FIBERGLASS SERIES - SG70MHM MHX CB845 Blend
Forum: rodboard

I have built using Fuji ECS, have not done a custom build using the Fuji ACS...anyone have any comments?? Are there any differences good or bad? Thank you in advance.
Forum: rodboard

Any help would be appreciated.... Pieces: 1 | Length: 7’0” | Line: 12 - 20lb. | Lure Weight: 3/8 - 3/4oz | Power: Medium Heavy | Action: Moderate Fast Thank you in advance
Forum: rodboard

Have seen the all Cork rear grip on some Dobyns rods too
Forum: rodboard

HESGRG4.5S-350 Batson Forecast Cork Length 4.50 O.D. 1.06 I.D. 0.35 Might be chasing a pink elephant.....Looking for all cork rear split grip with specs very similar to the above.....can purchase cork/composite (above) with these specs but not all cork....These handles are very similar to what is found on some of the Falcon Rod models...including the latest Lowriders...can get all cork b
Forum: rodboard

yes I am...used 1/8 in. masking tape....I figured out how to utilize it best...was able to finish last rod guide...ready to apply epoxy on thread....I really appreciate all the thoughts,,,this forum is terrific
Forum: rodboard

I am new to the rod building obsession and have a question for those who are more experienced than me. Would it possible to use the regular ol' "dime store" glue stick to temporarily put the small guides in place until they can be wrapped or at least long enough to allow me to tape them down with masking tape? I will purchase some guide adhesive but will not be able to receive the adh
Forum: rodboard

Newbie question...is it absolutely necessary to use either tape or an arbor for reel seat base or can you just epoxy reel seat to blank if it is a close fit??
Forum: rodboard

Big THANKS to all of you who responded...I appreciate the info. I was thinking that Plano 3600 boxes would be the way to go....All of you all affirmed it.
Forum: rodboard

Anyone have a good idea for storage of unused rod guides??
Forum: rodboard