SPONSORS
2024 ICRBE EXPO |
Results 1 - 30 of 137
10 years ago
ridge orjalesa
how much of an idiot do you have to be to step on the prong that is attached to a motor?
Forum: rodboard 10 years ago
ridge orjalesa
Mark, where did you find the drag rating of the phenix?
i saw only see the line listing and no drag rating at 60degrees.
thanks.
Forum: rodboard 10 years ago
ridge orjalesa
Hello,
based on my research when you set up a vertical jigging rod using a spinning reel 10,000 or smaller the gudies are as follows, 30-20-16-12-10-10 tiptop 10. no most 5'4''-5'6'' rods. Why can't you go 30-20-12-8-8-8-tiptop 8 or 30-20-12-10-10-10 tiptop 10 ?
Forum: rodboard 10 years ago
ridge orjalesa
what do you mean fully adjustable, can you please try to elaborate?
thanks.
Forum: rodboard 10 years ago
ridge orjalesa
6. fuji china
is it true that fuji is made in china now?
Forum: rodboard 10 years ago
ridge orjalesa
why is it not strong enough for tarpon ?
you beat the fish wiith the rod?
Forum: rodboard 10 years ago
ridge orjalesa
9. dryer motor
how many watts for a rod dryer motor?
synchronous or not?
any particular brand?
thanks.
Forum: rodboard 10 years ago
ridge orjalesa
10. Re: Decals
for me, the better one of the two is waterslide. peel n stick are kinda thick compared to waterslide and follows the contour better than peel n stick.
easy to get the bubbles out, easy to install, easy to move around to straighted it parallel to the blank. no other solvent needed, just distilled water.
Forum: rodboard 10 years ago
ridge orjalesa
11. Re: Decals
Threre's a guy in the nerbs facebook page that prints decals on waterslide ,he advertised it as $45 per sheet.
I got a sheet from him and they were real good. I got half of the sheet in silver and half in gold.
Forum: rodboard 10 years ago
ridge orjalesa
is there any other purpose on putting finish on the underwraps other than it helps in wrapping the overwrap so it won't dig?
Forum: rodboard 10 years ago
ridge orjalesa
13. decal solution
where can i get the solution where you spray on the peel and stick decal and allows you to move the decal a little bit..
decalcon no longer sells those.
Forum: rodboard 10 years ago
ridge orjalesa
i'm sure it was deisgned as well as it could be deisgned. out of the hundreds of people who bought the lathe with the attachment, you're the only one who complains about it not designed right. perhaps you should design your own, find a machine shop to machine it according to your specs.
Forum: rodboard 11 years ago
ridge orjalesa
16. Re: lathe chuck
just called teknatool and they said they have the "JSPIN" jaw that will fit the teknatool midi chuck and it would grip upto 1/4", cost is $56.
Forum: rodboard 11 years ago
ridge orjalesa
17. Re: lathe chuck
roger, the lathe is a rockler mc1018.
Tom, the chuck is a teknatool 4 jaw precision midi chuck.
the jacobs chuck goes to about 1/2 inch that is keyed, i tried to tap it into the headstock with a rubber mallet and it takes it, MT2.
but i dont want to use the jacobs chuck in the headstock because i want it int he tailstock, since it is keyed, i want it to grip the mandrel so it wont come flyin
Forum: rodboard 11 years ago
ridge orjalesa
18. Re: lathe chuck
the tailstock has the 1/2 inch jacobs chuck. how will i connect it to the head stock?
i tried putting the jacobs chuck to the headstock but the metal thing that goes inside the headstock slipped.
BTA, $200 for the midi lathe, teknatool 4 jaw chuck and jacobs chuck, is it a good deal?
Forum: rodboard 11 years ago
ridge orjalesa
19. lathe chuck
I just got a lathe off craigslist but the lathe came with a teknatool 4 jaw self centering chuck that only goes down to 1/2 inch, i would like to go as small as 1/4 inch so i can grip a 1/4inch mandrel.
what will I purchase so i can grip 1/4inch?
Forum: rodboard 11 years ago
ridge orjalesa
hey Don, i've read that in order for the resin to really take full advatnage of its technology, you'll have to autclave it during the process. is it true?
Forum: rodboard 11 years ago
ridge orjalesa
that's a nice copy, will the carriage slide up/down the blank smoothly?
Forum: rodboard 11 years ago
ridge orjalesa
heavy saltwater boat rod 80# 6'4''. i just want to use the 20 to make sure the line doenst hit the hand. i've built a spiral using 16-12-12-12--10 running guides but i have never built using a 20, jsut wondering what size to use after the 20.
Forum: rodboard 11 years ago
ridge orjalesa
i have a question that pertains to this spiral wrap so i'll just post here.
if you are doing a slow spiral (3 guide transition) and start with a 20 at 0degrees, what's the next size to use at the 60degrees, can i use a 16 or a 12?
i want the running guides to be 10's.
can i make it like this 20 (0) - 16 (60) - 12 (120) - 10(180) all the way to the tip?
Forum: rodboard 11 years ago
ridge orjalesa
cartridges are not hard to find.
they are vailable and plenty if you know where to look.
theya re available from a guy in new zealand at a reasonable price cheaper than the @#$%& hoarders who led you to believe that the cartridges are becoming instinct.
Also,
pawis parker foil fast p21x uses the same cartridges, the pawis parkers is basically an alps 5000, it has USA tech support, inks by the
Forum: rodboard |