SPONSORS
2024 ICRBE EXPO |
Current Page: 1 of 1
Results 1 - 15 of 15
13 years ago
vaughn darmer
Any one know the company that was selling tee shirts w/ the international rod builds logo!
Mine is almost worn out, thanks
Forum: rodboard 13 years ago
vaughn darmer
Also use the 1x30 sander for guide prep. But found micron belts for it, no need to polish. they come out perfect
Forum: rodboard 13 years ago
vaughn darmer
3. rod repair
Need to replace a wire guide on a 30 year old shakspear wonderod.
what kind of thread sealer did they use then, varnish! will using flex coat
lite be all right
Forum: rodboard 14 years ago
vaughn darmer
Have a 903 fly rod where the two sections where not seated correctly. Tip section came loose & broke off 1/4 inch of
the male ferrule on the butt section. Still have 1 1/2 inch overlap. Will glueing an insert inside the male ferrule section
strength it ok. There was some splittering. If I cut the end down, the tip section will not fit. Will change the ID/OD
Forum: rodboard 14 years ago
vaughn darmer
Volume 12 - Issue 1 what make lathe is shown in photo?
Model # Ect.
Forum: rodboard 15 years ago
vaughn darmer
6. Kokanee rods
Bought 2- 7' foot kokanee rod blanks at the lamiglass meet in washington.
there made of fiberglass, was told they need a graphite insert for the butt
section to stiffin the butt section so they can handle a down rigger.
how long should the insert be!!!!
Forum: rodboard 15 years ago
vaughn darmer
Found a 1 1/2 " gasket plug cutter to cut the rings for a grip. But what do I use
to shape the grip, same as cork. Coures file and sand paper! I assume the
center bore would be the same type of fit as cork or should it be slightly
undersize!
what is the best adhesive for mounting finished grip to blank, rod bond,
2 part epoxy ect !
Yes I did read the article in Vol 11-Issue 3 its
Forum: rodboard 15 years ago
vaughn darmer
What causes flex coat part A resin to turn milky white, and form small
lumps . Has happened to me twice. This morning I used a lighter to
heat the finnish and the small lumps disappered. I quess this means the
resin is no longer good!
Forum: rodboard 15 years ago
vaughn darmer
9. Lathes
Where can I find info on lathe makers, brand names & address
web sites thanks
Forum: rodboard 17 years ago
vaughn darmer
bought a old trolling rod to refinnish, but need to remove the wood foregrip
so I can replace the reel seat, I can cut the reel seat off, but I dont want
to cut the foregrip as it has all wood grips in excellent shape.
any ideas.
Forum: rodboard 17 years ago
vaughn darmer
11. 1" belt sanders
Trying to find a good 1" belt sander for doing guide feet. Trouble is I can only
find 120 grit belts, when I want 220 grit or finer.
any ideas for a source
Forum: rodboard 17 years ago
vaughn darmer
12. humidity
Will humidity created by a swamp cooler effect rod wrapping thread,
and finnish. Thought I heard thread should be kept in zip locks bags.
Forum: rodboard 17 years ago
vaughn darmer
13. 9 piece fly rod
how do you spline a 9 piece fiberglass fly blank.
or do you foreget about it, and make sure it is
straight, is good enough! it a lamiglass
FL 8439 blank
Forum: rodboard 18 years ago
vaughn darmer
at the april meeting in woodland you and jim mick where talking about
spiral wraps for any rod when you do not have a reel. Could you please
give me your views on this. The rod is a 81/2 ft steelhead blank, casting.
you seemed to have a generic set for this situation
Vaughn
Forum: rodboard 18 years ago
vaughn darmer
15. Spiral wrap
Is there a generic, one size fits all spiral wrap when you do not have a
reel to do the setup. the rod is a rainshadow HS 1023 , 81/2 ft steelhead
blank for casting. what would be the pacing on the first 3 quides?
Some one at the woodland meeting mentioned a spacing that works
on all rods when you do not know the reel to be used
Forum: rodboard
Current Page: 1 of 1
|