SPONSORS
2024 ICRBE EXPO |
Current Page: 1 of 1
Results 1 - 19 of 19
12 years ago
jim ellis
can you e-mail me? John Sams your e-mail was undeliverable. Jim
Forum: rodboard 12 years ago
jim ellis
I am having trouble with very small guides. I cannot get the tape to hold the guide while I wrap. any help appreciated.
Forum: rodboard 13 years ago
jim ellis
3. reamers
Can anyone tell me how to make reamer from old rod blanks?. are they useable in an electric drill? Thanks in advance
Forum: rodboard 15 years ago
jim ellis
How did you make the stands? where did you get the rollers? Can you e-mail me?
Forum: rodboard 15 years ago
jim ellis
5. Renzetti
Can any one tell me the cost of a Renzetti? How many extras do you need to buy.
Thanks
Forum: rodboard 16 years ago
jim ellis
6. Re: hotel
Tom
I had my little dog there last year at the Radison. I think the lady Mr Upton is refering to was my wife. Sorry I will miss this year.
Jim Ellis
Not Jimi from Decal Connection
Forum: rodboard 16 years ago
jim ellis
7. Re: Rod Expo
Sorry for the confusion. I did not think of that part when I posted. SORRY
Jim Ellis
Lake Crystal, Mn
Forum: rodboard 16 years ago
jim ellis
8. Rod Expo
I just want to wish everyone a great time at the Expo. I have attended the last 3 and loved every minute. My wife just had very serious heart surgery and is unable to travel due to 3 times a week Dialysis. Have a great time---I will miss not being with you.
Forum: rodboard 16 years ago
jim ellis
Paul,
I think you would have to register at the photo forum too. Just reg. by clicking on the upper right I think.
Jim Ellis
Forum: rodboard 17 years ago
jim ellis
Tom,
Do we need to cut the ticket out of the magazine or will photo copies work? Hate to cut up my magazine.
Thanks
Forum: rodboard 17 years ago
jim ellis
11. motor rotation
I am wiring a small 6 RPM motor. if I direct wire it with no switch it runs clock wise. If I put a switch in it run counter clockwise. Any ideas what to do to get it to run clockwise with a swittch???
Forum: rodboard 17 years ago
jim ellis
12. Re: Who's Going?
Got room and will drive from the great state of Minnesota. Loved it last year. I don't post often but will be there.
Jim Ellis
Forum: rodboard 17 years ago
jim ellis
Tom and the rest of the rod building community,
I will try to give a breief run down of the things I remember from the event. Jason was given 2 rods. One a bait casting rod and reel and the other a spinning rod and reel. I did donate 100.00 for one of the reels. He was also given an ice fishing rod and reel from a builder here in Minnesota I believe. He was also given a tackle box with tackle, s
Forum: rodboard 17 years ago
jim ellis
I Just want to mention that the Rods that were built for Jason Mcnamara were given to him at the American Legion In Lake Crystal, Minnesota. Jason was excited to get the rods. He has used them and he cannot say enough good about the rod building community. I was there when he was given the rods. I too am very disappointed that this has fallen by the way side as there was a great response from the
Forum: rodboard 17 years ago
jim ellis
17. veteran rods
I just wanted to make a post to thank every one for the generous support for Jason McNamara's project. It turned out auwsome. Jason was suprised and could not even express himself. He really did appreciate the support. Jeff did an excellent job with the presentation. Today I had several locals stop me on the street to tell me how much they enjoyed going to see the BEAUTIFUL FISHING RODS. Most peo
Forum: rodboard 18 years ago
jim ellis
18. Steven Penzes
Steve would you e-mail me at jellis110@mchsi.com
Forum: rodboard 18 years ago
jim ellis
19. drilling wood
I am having problems drilling wood handles. I tried in the square and the bit wonders like a drunken sailor. Any suggestions? I am drilling on my lathe, slow speed 3/8 inch Brad poit bit
Forum: rodboard
Current Page: 1 of 1
|